Network Dome Camera Quick Start Guide 1
Network Dome Camera·Quick Start Guide About this Manual This Manual is applicable to DS-I127 DS-I227 Dome Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Network Dome Camera·Quick Start Guide Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Network Dome Camera·Quick Start Guide EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Network Dome Camera·Quick Start Guide These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Network Dome Camera·Quick Start Guide ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
Network Dome Camera·Quick Start Guide camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep the camera away from liquid while in use. ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture. ● Regular part replacement: a few parts (e.g.
Network Dome Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 10 1.1 Type I Camera ............................................................... 10 1.1.1 Overview ............................................................ 10 1.1.2 Cable Description ............................................... 12 1.2 Type II Camera .............................................................. 13 1.2.1 Overview ........................
Network Dome Camera·Quick Start Guide 4 Accessing via Web Browser ..........................................................
Network Dome Camera·Quick Start Guide 1 Appearance Description Cameras of this series belong to two appearance types. 1.1 Type I Camera Type I camera has different models. Some models have the lens that zoom and focus levels must be manually adjusted via zoom/focus lever and some models have a motor-driven lens that zoom and focus adjustment can be completed via web browser or client software. Please refer to the actual device. 1.1.1 Overview The overview of the Type I network dome camera is shown below.
Network Dome Camera·Quick Start Guide 5 8 6 7 Figure 1-2 Overview of Type I Camera (2) Table 1-1 Overview of Type I Camera No.
Network Dome Camera·Quick Start Guide 1.1.2 Cable Description Cable description of the Type I network dome camera is shown below. Note: Cables vary according to different models as the figures below.
Network Dome Camera·Quick Start Guide Table 1-2 Cable Description No. Description 9 Network Interface 10 Power Supply Interface 11 Audio/Alarm Interface 12 Audio Input and Output Interface 13 Video Output Interface 14 Alarm Input and Output Interface Notes: Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, and port No., etc. Some of the models support audio and alarm functions. 1.
Network Dome Camera·Quick Start Guide 1.2.1 Overview The overview of the Type II network dome camera is shown below.
Network Dome Camera·Quick Start Guide 6 Unit: mm Overview of Type II Camera (3) Overview of Type II Camera No.
Network Dome Camera·Quick Start Guide 1.2.2 Cable Description Cable description of the Type II network dome camera is shown below. Note: Cables vary according to different models as the figures below.
Network Dome Camera·Quick Start Guide Table 1-4 Cable Description No. Description 6 Power Supply Interface 7 Network Interface 8 Alarm Input and Output Interface 9 Audio Input and Output Interface 10 Auxiliary Video Interface Notes: Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, and port No., etc. Some of the models support audio and alarm functions.
Network Dome Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or PoE (802.3af), please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Dome Camera·Quick Start Guide Preparation Purpose: Before mounting, you have to disassemble the camera and install the memory card first. 2.1.1 Disassembling Steps: 1. Loosen the three screws on the edge of the bubble with the screw driver. 2. Lift and put aside the bubble. 3. Remove the inner black liner.
Network Dome Camera·Quick Start Guide Black Liner Bubble Screws Remove the Bubble and Black Liner (Type II Camera) 2.1.2 Memory Card Installation Steps: 1. Rotate the camera body to completely expose the memory card slot. 2. Insert the memory card into the memory card slot, and push to get it mounted.
Network Dome Camera·Quick Start Guide Memory Card Memory Card Slot Install the Memory Card (Type I Camera) Memory Card Slot Install the Memory Card (Type II Camera) 3. (Optional) To unmount the memory card, push to eject it.
Network Dome Camera·Quick Start Guide Mounting Installation of type I camera and type II camera are similar. We take type I camera as an example in this manual. 2.2.1 Ceiling Mounting Steps: 1. Attach the drill template (supplied) to the place where you want to fix the camera. 2. Drill three screw holes in the ceiling.
Network Dome Camera·Quick Start Guide Front Drill Template Hole A: Route cables through the ceiling. Hole B: Side outlet. Hole 1: Fix the mounting base. Please use Φ5.5mm drill to install expansion screws. The Drill Template (Type II Camera) Notes: ● The drill template varies according to the different camera model as the figures below. Please refer to the actual device. ● If you want to route the cables inside the ceiling, drill a cable hole in the ceiling according to the drill template.
Network Dome Camera·Quick Start Guide Back Box Screws Secure the Camera 4. Adjust the surveillance angle, zoom and focus level. Refer to the Section 2.3 for detailed information. 5. Install the inner black liner back to the camera. 6. Install the bubble back to the camera and secure it with screws.
Network Dome Camera·Quick Start Guide Conduit Installation on the Side If you want to route the cables from side of the camera, you need to install a conduit for cable routing. Steps: 1. Rotate the water-proof plug counterclockwise to remove it from the camera. Side Cable Outlet Water-proof Plug Remove the Water-proof Plug 2. Route the cables through the side outlet to the conduit. 3. Align and rotate clockwise the conduit to the side outlet tightly.
Network Dome Camera·Quick Start Guide Note: For wall mounting, position the side outlet directly downward for water-proof. Downward Side Outlet Direction 2.2.2 In-ceiling Mounting Before you start: In-ceiling mounting bracket is not included in package. If you choose this mounting type, you have to prepare a bracket first. The in-ceiling mounting bracket shown in below is only for demonstration. Steps: 1. Cut a hole in the ceiling according to the size of the in-ceiling mounting bracket.
Network Dome Camera·Quick Start Guide Main Body Ceiling Hole Size Rim In-ceiling Mounting Bracket Cut a Hole for In-ceiling Mounting 2. Align No.1 screw holes with the corresponding screw holes on the bracket, and secure the mounting base to the bracket with screws. In-ceiling Mounting Bracket Mounting Base No.1 Screw Holes Install Mounting Base 3. Align the screw holes for camera fixing, and secure the camera to the mounting base.
Network Dome Camera·Quick Start Guide In-ceiling Mounting Bracket Mounting Base Camera Screw Holes for Camera Fixing Install the Camera to the Mounting Base 4. Place the bracket and camera to the hole in ceiling, and screw the toggle bolt clockwise to fix the bracket in ceiling.
Network Dome Camera·Quick Start Guide Toggle Bolts: screw them clockwise Toggle Bolts: fix the bracket Fix the Bracket in Ceiling 5. Adjust the surveillance angle, refer to Section 2.3. 6. Install the black liner and the bubble back to the camera. Install the Black Liner and the Bubble 7. Install the rim to the bracket.
Network Dome Camera·Quick Start Guide Rim Rim Install the Rim 2.2.3 Mounting with Wall Mounting Bracket Before you start: Wall mounting bracket is not included in package. If you choose this mounting type, you have to prepare a bracket first. The wall mounting bracket shown in below is only for demonstration. Note: When choosing a wall mounting bracket, you must pay attention to the size of the cap which should match the mounting base of the camera.
Network Dome Camera·Quick Start Guide Steps: 1. Route the cables, install the wall mounting bracket, and secure the cap on the bracket. Wall Mounting Bracket Cap Install Wall Mounting Bracket 2. Align the screw holes of the mounting base with the corresponding screw holes of the cap. 3. Secure the mounting base to the cap with screws. Cap Mounting Base Install the Mounting Base 4. Align the camera with the mounting base, and secure the camera with screws.
Network Dome Camera·Quick Start Guide Secure the Camera 5. Connect the video output connector to the monitor. Connect the power connector to the power supply. 6. Adjust the image and focus. Please refer to the section 2.3 for more detailed information. 7. Install the inner black liner back to the camera. 8. Secure the bubble to the camera with screws.
Network Dome Camera·Quick Start Guide Secure Black Liner and Bubble 2.2.4 Mounting with Pendant Mounting Bracket Before you start: Pendant mounting bracket is not included in package. If you choose this mounting type, you have to prepare a bracket first. The pendant mounting bracket shown in below is only for demonstration. Note: When choosing a pendant mounting bracket, you must pay attention to the size of the cap which should match the mounting base of the camera.
Network Dome Camera·Quick Start Guide Size of the Mounting Base Steps: 1. Route the cables and Install the pendant mounting bracket. Secure the cap on the bracket. Pendant Mounting Bracket Cap Install the Pendant Mounting Bracket 2. Align the screw holes of the mounting base with the corresponding screw holes of the cap.
Network Dome Camera·Quick Start Guide 3. Secure the mounting base to the cap with screws. Cap Mounting Base Install the Mounting Base 4. Align the camera with the mounting base, and secure the camera with screws.
Network Dome Camera·Quick Start Guide Secure the Camera 5. Adjust the image and focus. Please refer to the section 2.3 for more detailed information. 6. Install the inner black liner back to the camera. 7. Secure the bubble to the camera with screws. Secure Black Liner and Bubble 2.2.5 Mounting with Gang Box Steps: 1. Install the gang box in the ceiling or the wall. 2. Attach the mounting base to the gang box with two screws.
Network Dome Camera·Quick Start Guide Gang Box Mounting Base Install the Mounting Base 3. Route the cables through the hole in the center of the mounting base. 4. Align the camera with the mounting base. And secure the camera with screws.
Network Dome Camera·Quick Start Guide 5. Adjust the image and focus. Please refer to the section 2.3 for more detailed information. 6. Install the inner black liner back to the camera. 7. Secure the bubble to the camera with screws. Secure the Black Liner and Bubble 2.3 Image and Focus Adjusting Before you start: Connect the camera to a monitor with supplied auxiliary video output cable, and power on the camera.
Network Dome Camera·Quick Start Guide Note: For certain camera models, the auxiliary video cable is not included in the package. Instead, you can connect the video out interface of the camera to a monitor for image and focus adjustment. Video Out Interface Video Out Interface of the Camera 2.3.1 3-Axis Adjustment Steps: 1. View the camera image using the monitor. 2. Rotate the panning table to adjust the panning position of the camera. 3.
Network Dome Camera·Quick Start Guide Pan: 0° to 355° Tilt: 0° to 90° Rotate: 0° to 355° 3-axis Adjustment (Type I Camera) Tilt: 0° to 70° Pan: 0° to 355° Rotate: 0° to 355° 3-axis Adjustment (Type II Camera) 2.3.2 Zoom and Focus Adjustment. Manually Adjustment: Some camera models of this series have the lens that zoom and focus levels must be manually adjusted via zoom/focus lever and you can use zoom lever and focus lever to adjust the lens.
Network Dome Camera·Quick Start Guide 1. View the camera image using the monitor. 2. Loosen the zoom lever and move the lever between T (Tele) and W (Wide) to obtain the appropriate angle of view. Zoom/Focus Lever Zoom/Focus Lever (Type I Camera) Zoom/Focus Lever Zoom/Focus Lever (Type II Camera) 3. Tighten the zoom lever. 4. Loosen the focus lever and move the lever between F (Far) and N (Near) to obtain the optimum focus. 5. Tighten the focus lever.
Network Dome Camera·Quick Start Guide Motor-driven Lens: Some camera models of this series are equipped with a motor-driven lens. You can adjust the zoom and focus level on PTZ control panel by visiting the camera via web browser or client software.
Network Dome Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 3.1 Wiring Please connect to the camera to the network according to the following figures.
Network Dome Camera·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Dome Camera·Quick Start Guide 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create to a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Dome Camera·Quick Start Guide Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch. Please refer to the user manual of SADP software for details. 3. Create a password and input the password in the password field, and confirm the password.
Network Dome Camera·Quick Start Guide 4. Click OK to save the password. You can check whether the activation is completed on the popup window. If activation failed, please make sure that the password meets the requirement and try again. 3.3 Modifying the IP Address Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP software or client software to search and change the IP of network camera.
Network Dome Camera·Quick Start Guide Figure 3-5 Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details.
Network Dome Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Dome Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.