Camera Network Bullet Camera Quick Start Guide 0
Network Bullet Camera·Quick Start Guide About this Manual This Manual is applicable to DS-I126 DS-I226 Network Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Network Bullet Camera·Quick Start Guide Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Network Bullet Camera·Quick Start Guide EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Network Bullet Camera·Quick Start Guide These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Network Bullet Camera·Quick Start Guide ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
Network Bullet Camera·Quick Start Guide camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep the camera away from liquid while in use. ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture. ● Regular part replacement: a few parts (e.g.
Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ................................................................. 8 1.1 Type I Camera ................................................................. 8 1.2 Type II Camera .............................................................. 10 1.3 Type III Camera ............................................................. 12 2 Installation ....................................................................................
Network Bullet Camera·Quick Start Guide 1 Appearance Description 1.1 Type I Camera The overview of Type I camera is shown in below. 1 4 10 11 6 5 13 12 8 2 3 7 9 Overview of Type I Camera Description No.
Network Bullet Camera·Quick Start Guide No. Description 3 Zoom and Focus Lever 4 IR LED 5 Lens 6 Air Vent 7 Video Output Interface 8 Reset Button 9 Memory Card Slot 10 Audio Cable 11 Alarm Cable 12 Power Cable 13 Network Cable Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Bullet Camera·Quick Start Guide 1.2 Type II Camera The overview of Type II camera is shown below.
Network Bullet Camera·Quick Start Guide Description No.
Network Bullet Camera·Quick Start Guide Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 1.3 Type III Camera The overview of type I camera is shown below.
Network Bullet Camera·Quick Start Guide 14 Overview of Type III Camera (2) Description No.
Network Bullet Camera·Quick Start Guide No. Description 10 Network Cable 11 Power Cable 12 Alarm Cable 13 Audio Cable Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or PoE (802.3af), please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Bullet Camera·Quick Start Guide 2.1 Memory Card Installation This series of cameras support memory card installation. Different camera types share the similar installation steps, and we take Type I camera as an example. Steps: 1. Rotate the lock screw counterclockwise to loosen it. Slide the sun shield according to the arrow direction as shown in below. Lock Screw Loosen the Lock Screw 2. Remove the sun shield.
Network Bullet Camera·Quick Start Guide Figure 2-2 Remove the Sun Shield 3. Remove the front cover by rotating it counterclockwise. 4. Insert the memory card into the memory card slot. Figure 2-3 Insert the Memory Card 5. Rotate the front cover clockwise back to the camera and install the sun shield back. 6. Tighten the lock screw clockwise to tighten the sun shield.
Network Bullet Camera·Quick Start Guide Rotating Label Tighten the Front Cover For water-proof performance, align the rotating label on the front cover with that on the camera when you rotate the front cover clockwise. 2.2 Type I Camera Mounting 2.2.1 Wall Mounting Before you start: Wall mounting bracket is not included in the package. You need to purchase a bracket separately. Steps: 1. Install the wall mounting bracket to the wall with supplied screws.
Network Bullet Camera·Quick Start Guide Pedestal Figure 2-5 Install the Wall Mounting Bracket Insert the expansion screws first if the camera is mounted to a cement wall. And you can use the self-tapping screws directly if the camera is mounted to a wooden wall. 2. Align the camera to the pedestal of the bracket, and fix the camera with the supplied screws. Figure 2-6 Install the Camera to the Bracket 3. Adjust the view angle.
Network Bullet Camera·Quick Start Guide 1). Loosen the pan adjusting screw to adjust the panning position [0° to 360°]. Tighten the screw. 2). Loosen the tilt adjusting screw to adjust the tilting position [0° to 90°]. Tighten the screw. 0° to 90° Pan Adjusting Screw 0° to 360° Tilt Adjusting Screw Figure 2-7 Adjust View Angle 4. Adjust zoom and focus (refer to Section 2.4). 5. (Optional) Install the water-proof jacket for network interface. Refer to Section 2.5 for detailed installation procedures. 2.
Network Bullet Camera·Quick Start Guide Ceiling Pendant Bracket Adjusting Knob Notch Nut Figure 2-8 Fix the Pendant Bracket 2. Loosen and remove the Lock Screw on the sun shield of the camera. 3. Screw the camera to the pendant bracket through the Lock Screw hole. Tighten the nut to secure the camera.
Network Bullet Camera·Quick Start Guide Figure 2-9 Secure the Camera 4. Adjust the view angle as shown in Figure 2-10. 1). Loosen the adjusting knob. 2). Rotate the notch to face or be back to your surveillance scene according to your actual need. To obtain larger angel adjustment range, place the notch back to the surveillance scene if your camera monitors downwards, and place the notch facing the surveillance scene if your camera monitors upwards. 3). Adjust panning position from 0° to 360°. 4).
Network Bullet Camera·Quick Start Guide Figure 2-10 Adjust the View Angle 5. Adjust zoom and focus (refer to Section 2.4). 6. (Optional) Install the water-proof jacket for network interface. Refer to Section 2.5 for detailed installation procedures. 2.3 Type II and Type III Camera Mounting Before you start: Camera of these types is equipped with a bracket. It can be mounted to a wall or a ceiling directly and can also be mounted with a junction box or a gang box. 2.3.1 Direct Mounting Steps: 1.
Network Bullet Camera·Quick Start Guide Drilling Holes in the Wall 3. If you need to route cables through the wall (or the ceiling), cut a cable hole according to the drill template. Skip this step, if you want to route the cables on the surface of the wall (or the ceiling). 4. Route the cables of the camera. 5. Secure the camera to the wall (or the ceiling) with expansion screws. Drill Template Drill Template Secure the Camera 6. Adjust the view angle.
Network Bullet Camera·Quick Start Guide 3). Tighten the lock screw 1. Tilt Adjustment Steps: 1). Loosen the lock screw 2. 2). Adjust the tilting position of the camera. The adjusting range is from 0° to 100°. 3). Tighten the lock screw 2. Rotation Adjustment Steps: 1). Loosen the lock screw 3. 2). Rotate the rotation position to adjust the azimuth angle of the image. The adjusting range is from 0° to 360°. 3). Tighten the lock screw 3.
Network Bullet Camera·Quick Start Guide 8. (Optional) Install the water-proof jacket for network interface. Refer to Section 2.5 for detailed installation procedures. 2.3.2 Mounting with a Junction Box Before you start: The junction box is not included in the package. You need to prepare one for this mounting type. Steps: Junction Box Safety Rope Figure 2-14 Mounting with a Junction Box 1. Attach the drill template (supplied) to the wall where the camera is to be mounted. 2.
Network Bullet Camera·Quick Start Guide 4. Secure the junction box to the wall (or the ceiling) with expansion screws. 5. Hook the camera to the junction box with the safety rope. 6. (Optional) Install the water-proof jacket for the network interface. Refer to Section 2.5. 7. Route the cables of the camera. 8. Connect the interfaces to the power on the camera to see if you can get an image on your monitoring screen.
Network Bullet Camera·Quick Start Guide 4. Connect the interfaces to the power on the camera to see if you can get an image on you monitoring screen. If you can’t get the image, check the connection of the interfaces before performing the next step. 5. Secure the camera to the camera attachment with screws. Gang Box Camera Attachment Figure 2-15 Mounting with a Gang Box 6. Adjust view angle. Refer to Step 6 in Section 2.3.1. 7. Adjust zoom and focus level. Refer to Section 2.4. 2.
Network Bullet Camera·Quick Start Guide Steps: 1. Remove the sun shield and front cover to expose the zoom lever and the focus lever. 2. View the camera image on the monitoring screen. 3. Loosen the zoom lever and move the lever between T (Tele) and W (Wide) to obtain the desired angle of view. 4. Tighten the zoom lever. 5. Loosen the focus lever and move the lever between F (Far) and N (Near) to obtain the optimum focus. 6. Tighten the focus lever. 7.
Network Bullet Camera·Quick Start Guide 2.4.2 Type III Type III camera is equipped with a motor-driven lens. You can adjust the zoom and focus level on PTZ control panel by visiting the camera via web browser or client software. For detailed steps, refer to the User Manual of Network Camera. Zoom and Focus Adjustment via Web Browser 2.
Network Bullet Camera·Quick Start Guide Table 2-1 Components No. Components 1 Camera’s Network Interface Socket 2 O-Type Gasket 3 Network Plug 4 Waterproof Endcap 5 Waterproof Rubber Gasket 6 Lock Nut 7 Network Cable from Router/Switch Steps: Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤ (the rubber gasket inset ridge must face the waterproof endcap), and the waterproof endcap ④ in order.
Network Bullet Camera·Quick Start Guide Insert the waterproof rubber gasket ⑤ into the waterproof endcap ④, and secure lock nut ⑥ with the waterproof endcap ④. Align the snap on the waterproof endcap ④ with the notch on the camera’s network interface socket ①, and then secure the waterproof endcap ④ to the camera’s network interface socket ① to finish installation. Align the snap and notch. i. Insert ⑤ into ④. ii. Secure ⑥ with ④.
Network Bullet Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 3.
Network Bullet Camera·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We take Activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Bullet Camera·Quick Start Guide 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet Camera·Quick Start Guide Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch. Please refer to the User Manual of SADP software for details. 3. Create a password and input the password in the password field, and confirm the password.
Network Bullet Camera·Quick Start Guide 4. Click OK to save the password. You can check whether the activation is completed on the popup window. If the activation failed, please make sure that the password meets the requirement and try again. 3.3 Modifying the IP Address Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC.
Network Bullet Camera·Quick Start Guide Figure 3-5 Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP. Please refer to the User Manual of SADP for details.
Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and versions above CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and versions above, Apple Safari 5.0.2 and versions above, Mozilla Firefox 5.0 and versions above and Google Chrome 18 and versions above Steps: 1. Open the web browser. 2.
Network Bullet Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the plug-in installation. Figure 4-2 Download Plug-in 6. Reopen the web browser after the plug-in installation and repeat steps 2 to 4 to login.
0
