Camera Network Bullet Camera Quick Start Guide 1
Network Bullet Camera·Quick Start Guide About this Manual This Manual is applicable toDS-I22T Network Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Network Bullet Camera·Quick Start Guide FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Network Bullet Camera·Quick Start Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
Network Bullet Camera·Quick Start Guide Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
Network Bullet Camera·Quick Start Guide ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Cautions ● Make sure the power supply voltage is correct before using the camera. ● Do not drop the camera or subject it to physical shock. ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently.
Network Bullet Camera·Quick Start Guide ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture. ● Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according to their average enduring time. The average time varies because of differences between operating environment and using history, so regular checking is recommended for all the users. Please contact with your dealer for more details.
Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ................................................................. 9 2 Installation .................................................................................... 10 2.1 Ceiling Mounting ........................................................... 11 2.2 Wall Mounting with a Junction Box ............................... 14 2.3 Wall Mounting with a Gang Box ....................................
Network Bullet Camera·Quick Start Guide 1 Appearance Description 3 DC12VIN 4 5 2 1 Figure 1-1 Overview Table 1-1 Description No.
Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Bullet Camera·Quick Start Guide Ceiling Mounting Steps: 1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template. 2 1 Ceiling Mounting 1 2 2 1:Screw Hole for Bracket 2:Screw Hole for Mounting Base 1 1 2 Figure 2-1 Drill Template 2. Fix the camera to the wall with the supplied screws. Note: Please insert the expansion screws first if the camera is mounted to the cement ceiling.
Network Bullet Camera·Quick Start Guide Figure 2-2 Install the Camera 3. Adjust the view angle. 1). Loosen No.1 lock screw to adjust the tilt angle [0°~100°]. 2). Loosen No.2 lock screw to adjust the pan angle [0°~360°]. 3). Loosen No.3 lock screw to rotate the camera [0°~360°]. 4). Tighten the lock screws.
Network Bullet Camera·Quick Start Guide 4. (Optional) Install the water-proof jacket for network interface. Note: It is recommended to adopt the water-proof jacket (supplied) for the network interface when the camera is installed outdoor. 1). If the network cable has been settled down, cut off the plug of the network cable first. 2). Route the network cable through the following components in sequence: fix nut, water-proof ring, and the main body of the water-proof jacket, as shown in the figure. 3).
Network Bullet Camera·Quick Start Guide Wall Mounting with a Junction Box 1. Drill the screw hole and cable hole according to the supplied drill template (shown as Figure 2-1). 2. Align the screw holes of the junction box to the drill template, and fix the junction box to the wall with screws. 3. Route the cables. 4. Fix the camera to the junction box with screws. 5. Adjust the view angle. For details, refer to Step 3 in Chapter 2.1. 6. (Optional) Install the water-proof jacket for network interface.
Network Bullet Camera·Quick Start Guide Wall Mounting with a Gang Box Note: An adapter plate should be purchased separately if you mount the camera to a gang box. Steps: 1. Install the adapter plate to the gang box. 2. Route the cables. 3. Fix the camera to the adapter plate with screws. 4. Adjust the view angle. For details, refer to Step 3 in Chapter 2.1. 5. (Optional) Install the water-proof jacket for network interface. For details, refer to Step 4 in Chapter 2. 1.
Network Bullet Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center.
Network Bullet Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software.
Network Bullet Camera·Quick Start Guide Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. SADP Interface Note: The SADP software supports activating the camera in batch.
Network Bullet Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click OK to save the password.
Network Bullet Camera·Quick Start Guide Note: Please refer to Chapter 3.2 to activate the camera if the camera is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP. Please refer to the User Manual of SADP for details.
Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Bullet Camera·Quick Start Guide 4. Click Login. Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Network Bullet Camera·Quick Start Guide Download Plug-in Install Plug-in (1) 24
Network Bullet Camera·Quick Start Guide Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2~4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.
0
