Network Speed Dome·Quick Start Guide Network Speed Dome Quick Start Guide i
Network Speed Dome·Quick Start Guide Quick Start Guide About this Manual This Manual is applicable to DS-P1420 DS-P2420 Network Speed Dome. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website.
Network Speed Dome·Quick Start Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Network Speed Dome·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death.
Network Speed Dome·Quick Start Guide Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. Please use the provided glove when open up the dome cover, avoid direct contact with the dome cover, because the acidic sweat of the fingers may erode the surface coating of the dome cover.
Network Speed Dome·Quick Start Guide Table of Contents 1 Installation ................................................................................................... 1 1.1 Connecting Cables .................................................................................................................... 1 1.2 Wall Mounting .......................................................................................................................... 2 1.2.1 Installing the Bracket ..........................
Network Speed Dome·Quick Start Guide 1 Installation Warning: Do not power the speed dome up until the installation is finished. To ensure the safety of personnel and equipment, all the installation steps should be done with power supply off. Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. When carrying the speed dome, do not directly pull waterproof group cables.
Network Speed Dome·Quick Start Guide 1.2 Wall Mounting 1.2.1 Installing the Bracket The speed dome can be installed to a thread interface or non-thread interface bracket. The non-thread bracket is highly recommended. When you select a thread bracket, please install the pendent adapter (supplied) between the bracket and speed dome. Any mismatch problems shall be taken responsibility by the user. 1 The dimension of pendant adapter is G12 .
Network Speed Dome·Quick Start Guide Figure 1-4 Drill Screw Holes Please take water-proof measures when installing outdoor speed domes. 1.2.2 Installing Micro SD Card Purpose: The speed domes are with built-in micro SD card slots which are for local storage with micro SD cards. There are four types of speed dome listed as follows. Mini IR network speed dome: The micro SD card slot is inside the rear cover. Outdoor mini IR network speed dome is taken as an example here.
Network Speed Dome·Quick Start Guide Scews Micro SD Slot Figure 1-6 Micro SD Card Slot (Mini IR Speed Dome Type II) 1.2.3 Speed Dome Installation IR Speed Dome Installation Steps: 1. Hang the safety rope to the speed dome and then hook to the bracket as shown in Figure 1-7. Figure 1-7 Mount the Dome 2. Route the cables of the speed dome through the bracket. 3. Connect the corresponding network/power cables. 4. Loosen the two lock screws on the bracket with the Allen wrench. 5.
Network Speed Dome·Quick Start Guide Figure 1-8 Tighten the Lock Screws 7. Remove the protective film on the IR light. The protective film may vary according to the models. Mini IR Speed Dome Type II Steps: 1. Drill holes in the ceiling. 1) Attach the drill template to the ceiling where you need to install the speed dome. 2) Cut a hole and drill screw holes according to the drill template. ±2mm of the diameter of the circle is tolerable. Figure 1-9 Drill Template 2. 3.
Network Speed Dome·Quick Start Guide Screws Figure 1-10 Install the Bracket 4. Align the toggle bolts with the screw holes on the ceiling and push the dome according to the direction of the arrow in the figure below to the mounting hole. 5. Rotate the screws clockwise and the toggle will automatically rotate down to secure the dome to the ceiling. Fix the locks on the ceiling.
Network Speed Dome·Quick Start Guide Ceiling Locks Locks Figure 1-12 Install the Dome to the Ceiling 6. Install the Trim Ring and finish the installation as shown in Figure 1-33.
Network Speed Dome·Quick Start Guide 2 Setting the Dome over the LAN You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 2.
Network Speed Dome·Quick Start Guide The default IP address of the speed dome is 192.168.1.64. Figure 2-2 Activation Interface(Web) 3. Create a password and input the password into the password field.
Network Speed Dome·Quick Start Guide Figure 2-3 SADP Interface 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. 4. Click OK to save the password.
Network Speed Dome·Quick Start Guide Figure 2-4 Modify the IP Address 4. Input the password and click Save to activate your IP address modification.
Network Speed Dome·Quick Start Guide 3 Accessing via Web browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 5 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Speed Dome·Quick Start Guide Figure 3-2 Download Plug-in Figure 3-3 Install Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. For detailed instructions of further configuration, please refer to the user manual of network speed dome.
