User manual

ManualsBrandsHIWATCH ManualsCorded CCTV SystemsHD-TVI CCTV camera 2,8 - 12 mm

TVI Turret & Bullet Camera

User Manual

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

0100001040924

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery that

cannot be disposed of as unsorted

municipal waste in the European

Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

UD.6L0201D1612A02

2012/19/EU (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

Please refer to the product specification for

camera parameters and functions.

This product and - if applicable - the

supplied accessories too are marked

with "CE" and comply therefore with

the applicable harmonized European

standards listed under the Low Voltage Directive

2006/95/EC, the EMC Directive 2004/108/EC,

the RoHS Directive 2011/65/EU.

TURBO HD

This series of camera adopts new generation

sensor with high sensitivity and advanced circuit

design technology. It features high resolution,

low image distortion and low noise, etc. , which

makes it suitable for surveillance system and

image processing system.

High performance CMOS sensor and high

resolution bring high-quality image;

Low illumination;

OSD menu, parameters are configurable;

Support auto white balance, auto gain control,

electronic shutter control;

Support image effect adjustment;

Unit transmission control;

Advanced 3-axis design meets different

installation requirements.

1 Introduction

1.1 Product Features

2 Installation

Check the specification of the products for the

installation environment.

Check whether the power supply is matched

with your power output to avoid damage.

Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

If the wall is the cement wall, you need to insert

expansion screws before you install the camera.

If the wall is the wooden wall, you can use

self-tapping screw to secure the camera.

If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

1.2 Overview

1.2.1 Overview of Type I Camera

1.2.2 Overview of Type Camera

Figure 1-1 Overview of Type I Camera

Figure 1-2 Overview of Type II Camera

2.1 Installation of Type I Camera

Steps:

1. Drill the screw holes and the cable hole on the

ceiling according to the supplied drill template.

Figure 2-1 The Drill Template

2.P ush the lock button to disassemble the camera

from the mounting base.

Figure 2-2 Release The Lock Screw

Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

Make sure that all the related equipment is

power-off during the installation.

3. Fix the mounting base to the ceiling.

Before you start:

Cameras in some models do not support OSD

menu. For actual operation, please refer to the

specification of each model.

4. Route the cables to the cable hole and connect

the corresponding cables.

5.Secure the camera to the mounting base by

supplied screws. Keep the word UP on the camera

being upright during the installation to make the

image showing normally.

Type

Model

Type I

DS-T116

DS-T226

Type II

DS-T119

DS-T228

This manual applies to the following models.

Summary of content (2 pages)

PAGE 1
.1 Product Features This series of camera adopts new generation sensor with high sensitivity and advanced circuit design technology. It features high resolution, low image distortion and low noise, etc., which makes it suitable for surveillance system and image processing system.
PAGE 2
3.Route the cables to the cable hole and connect the corresponding cables. 4.Fix the camera to the ceiling with the supplied screws. 3 Menu Operation Menu VIDEO. OUT DAY&NIGHT FRAME RATE COLOR AWB AUTO USER B/W HOLD AUTO AE SPECIAL EFFECT SYSTEM DC PRIVACY ZONE COLOR GAIN CAMERA ID ESC MOTION COLOR HUE ID DISP HOLD HLC SHARPNESS NAME DISP CONTRAST LANGUAGE BRIGHT FACTORY INIT 8000K Figure 2-3 Secure the Camera EXT EXIT 6000K 4200K 6.