HD-TVI Speed Dome Quick Start Guide
HD-TVI Speed Dome·Quick Start Guide Quick Start Guide About this Manual This Manual is applicable to the following models of HD-TVI Speed Domes. Model DS-TP2423 DS-TP1423 The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
HD-TVI Speed Dome·Quick Start Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
HD-TVI Speed Dome·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
HD-TVI Speed Dome·Quick Start Guide Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. Please use the provided glove when open up the dome cover, avoid direct contact with the dome cover, because the acidic sweat of the fingers may erode the surface coating of the dome cover.
HD-TVI Speed Dome·Quick Start Guide Table of Contents 1 Installation ........................................................................................................ 1 1.1 Connecting the Cables .............................................................................................................. 1 1.2 DIP Switch Settings ................................................................................................................... 2 1.2.1 Mini Speed Dome Settings .......................
HD-TVI Speed Dome·Quick Start Guide 1 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. There are several ways to install the analog speed dome. The wall mounting is taken as an example below. 1.1 Connecting the Cables Please turn the power off before connecting the cables. The cable interfaces of speed dome are shown in following figure. The cables are distinguished by different colors.
HD-TVI Speed Dome·Quick Start Guide 1.2 DIP Switch Settings . 1.2.1 Mini Speed Dome Settings DIP Switch Location of Mini Analog Speed Dome DIP Switch Figure 1-2 DIP Switch of Mini Analog Speed Dome Setting DIP Switch ON ON 1 2 1 DIP 2 3 4 5 6 7 8 9 10 Figure 1-3 Enlarged View of DIP Switch Table 1-2 Switch Functions Switch No.
HD-TVI Speed Dome·Quick Start Guide For convenient settings, refer to the following list to set the address for the speed domes. Table 1-3 Dome Address Switch No. 1 2 3 4 5 0 OFF OFF OFF OFF OFF 1 ON OFF OFF OFF OFF 2 OFF ON OFF OFF OFF 3 ON ON OFF OFF OFF … … … … … … 31 ON ON ON ON ON Dome Address Baudrate List For convenient settings, refer to the following list to set the baudrate for the speed dome.
HD-TVI Speed Dome·Quick Start Guide The speed dome is self-adaptive to private protocol when the No.8 and 9 switches are both OFF. TVI Mode For convenient settings, refer to the following list to set the TVI mode of the speed dome. Table 1-6 TVI Mode Switch No. TVI Mode 10 V2.0 OFF V1.0 ON Terminal Resistor Table 1-7 Terminal Resistor Switch No. 1 2 Turn on the Resistor ON ON Turn off the Resistor OFF OFF 1.3 Wiring and Installation There are several ways to install the speed dome.
HD-TVI Speed Dome·Quick Start Guide The wall must be thick enough to install the expansion screws. Please make sure that the wall is strong enough to withstand more than 8 times the weight of the dome and the mount. Steps: 1. Check whether the type of the bracket and the number of accessories are right, as shown in the figure below. Figure 1-4 Wall Mount Bracket, Nuts and Flat Washers 2.
HD-TVI Speed Dome·Quick Start Guide 1.3.3 Setting the DIP Switch Set the address and baudrate for the speed dome. The default value of DIP switch is shown below: Address: 0 Baudrate:2400 Terminal Resistor: OFF Please refer to the Section 1.2 DIP Switch Settings for DIP switch settings. 1.3.4 Installing the Speed Dome The sketches of installing the speed dome are for reference only. Steps: 1. Hang the safety rope to the speed dome and then hook to the mount as shown in Figure 1-7(left). 2.
HD-TVI Speed Dome·Quick Start Guide 2 Application and Operations 2.1 System Application The device can be controlled through the back-end device or control software. The back-end device includes control keyboard, DVR (Digital Video Recorder), etc., and the control software includes client software. Here we take the connection of DVR as the example.
HD-TVI Speed Dome·Quick Start Guide MAIN MENUS EXIT ENGLISH Figure 2-2 Main Menu Refer to the user manual for the detailed instruction to set the speed dome. 2.2.1 Configuring Patrol You can set the patrol function by the DVR and OSD menu, as well as the one-touch patrol can be realized. Configuring Patrol by DVR Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ Figure 2-3 PTZ Settings 2.
HD-TVI Speed Dome·Quick Start Guide Figure 2-4 Key point Configuration 4. Configure key point parameters, such as the key point No., duration of staying for one key point and speed of patrol. The key point is corresponding to the preset. The Key Point No. determines the order at which the PTZ will follow while cycling through the patrol. The Duration refers to the time span to stay at the corresponding key point. The Speed defines the speed at which the PTZ will move from one key point to the next. 5.
HD-TVI Speed Dome·Quick Start Guide 3. Up to 8 patrols can be configured. Edit the patrol. (1) Move the cursor to EDIT PATROL and click IRIS+ to enter edit mode. NUM PST DWELL SPEED 1 0 6 30 2 3 0 0 6 6 30 30 4 0 6 30 5 0 6 30 6 0 6 30 7 0 IRIS+ OK 6 30 IRIS- CANCEL Figure 2-6 Edit the Patrol (2) (3) 4. Click up/down direction buttons to choose the number and locate the preset to be edited.
HD-TVI Speed Dome·Quick Start Guide 2.2.2 Configuring Park Actions Purpose: For some certain model of the speed dome, it can be configured to start a predefined park action (scan, preset, patrol and etc.) automatically after a period of inactivity (park time). Configuring Park Actions by DVR Steps: 1. Click the button PTZ in the lower-right corner of the PTZ setting interface; Menu>Camera>PTZ 2. Click the button to show the one-touch function of the PTZ control. Figure 2-7 PTZ Panel - One-touch 3.
HD-TVI Speed Dome·Quick Start Guide MOTION AUTO FLIP ON PROPORTIONAL PAN ON PARK TIME PARK ACT 5 NONE SCAN SPEED IMAGE FREEZE 28 OFF DOME SPEED BACK 6 EXIT Figure 2-8 PTZ Configuration 2. 3. Move the cursor to the PARK TIME, and set the value in the range from 5 to 720 seconds. Move the cursor to the PARK ACT, and the action can be set as preset 1-8, pattern 1-5, patrol 1-10, pan scan, tilt scan, random scan, frame scan, panoramic scan, day mode, night mode, patrol-d or none.
HD-TVI Speed Dome·Quick Start Guide 3 Troubleshooting 3.1 Device Exceptions Question Why does the speed dome fail to start or repeatedly reboot? Why does the speed dome restart intermittently when controlling PTZ, calling presets or turning on the infrared lights of the IR dome at night? Answer Check the supply voltage of the dome. Ensure the supply voltage to meet the power requirements of the speed dome. The nearest power supply is recommended.
HD-TVI Speed Dome·Quick Start Guide Answer Please check whether the protective film of the bubble has been removed. Please check whether there are foreign objects on the bubble or the lens. Please check where there are obstructions such as spider web nearby. Open the bubble and check whether the lens cover has been removed. Restore the device to the default settings. Call the preset 95 to enter the OSD menu and select the RESTORE CAMERA.
