HD Vari-Focal Bullet & Turret & Dome Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Model Type I Camera HWT-B320-VF/HWT-B340-VF Type II Camera HWT-T320-VF/HWT-T340-VF Type III Camera HWT-D320-VF/HWT-D340-VF This manual may contain technical incorrect places or printing errors, and the content is subject to change without notice.
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage 1 Introduction 1.1 Product Features The main features are as follows: High performance CMOS sensor IR cut filter with auto switch OSD menu with configurable parameters Internal synchronization SMART IR mode 3-axis adjustment 1.2 Overview 1.2.
1.2.3 Overview of Type III Camera Switch Button Mounting Base Power Cord 12 VDC Video Cable IN DC12V Black Liner Bubble Note: Figure 1-3 Overview of Type III Camera Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.
2 Installation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Check whether the power supply is matched with your power output to avoid the damage. Make sure the wall is strong enough to withstand three times the weight of the camera and the bracket.
Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement wall, expansion bolts are required to fix the camera. For wooden wall, self-tapping screws are required. 5. Connect the corresponding power cord, and video cable. 6. Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the surveillance angle. 0° to 360° 1 2 0° to 90° 3 0° to 360° Figure 2-3 3-axis Adjustment 1) Loosen the No.
Figure 2-5 Drill Template Note: Drill the cable hole, when adopting the ceiling outlet to route the cable. 5. Attach the mounting base to the ceiling, and secure them with supplied screws Method 1 Method 2 Figure 2-6 Attach the Mounting Base to the Ceiling Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement ceiling, expansion bolts are required to fix the camera. For wooden ceiling, self-tapping screws are required. 6.
Pan Position [0° to 360°] Rotation Position [0° to 360°] Tilt Position [0° to 75°] Figure 2-8 3-axis Adjustment 1). Rotate the enclosure to adjust the pan position [0° to 360°]. 2). Move the camera body up and down to adjust the tilt position [0° to 75°]. 3). Rotate the camera body to adjust the rotation position [0° to 360°. 2.3 Installation of Type III Camera Before you start: Both wall mounting and ceiling mounting are suitable for the dome camera.
For cement ceiling, expansion bolts are required to fix the camera. For wooden ceiling, self-tapping screws are required. 5. Route the cables through the cable hole, or the side opening. 6. Connect the corresponding cables, such as power cable and video cable. 7. Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below to get an optimum angle.
3 Menu Description Purpose: Call the menu by clicking the button on the PTZ Control interface, or click Iris+. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. TVI DVR Camera Monitor Figure 3-1 Connection 2. Power on the analog camera, TVI DVR, and the monitor to view the image on the monitor. 3. Click PTZ Control to enter the PTZ Control interface. 4. Call the camera menu by clicking button, or click Iris+.
3.1 FORMAT You can set the format as 4MP@30fps, 4MP@25fps, 2MP@30fps, or 2MP@25ps. 3.2 EXPOSURE Exposure describes the brightness-related parameters, which you can set the EXPOSURE MODE as GLOBAL, BLC, or DWDR. GLOBAL GLOBAL refers to the normal exposure mode which performs exposure according to the whole image brightness.
AUTO Automatically switch Color, or BW (Black and White) according to actual scene brightness. You can turn on/off the IR LIGHT, and set the value of SMART IR in this menu. DAY/NIGHT MODE IR LIGHT SMART IR D à N THRESHOLD N à D THRESHOLD BACK EXIT SAVE & EXIT AUTO ON 2 2 7 Figure 3-4 AUTO IR LIGHT You can turn on/off the IR LIGHT to meet the requirements of different circumstances.
CONTRAST This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 9. SHARPNESS Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 9. SATURATION Adjust this feature to change the saturation of the color. The value ranges from 1 to 9.
