User guide

ManualsBrandsHK Audio ManualsAudioFirNet Manual

FIRNET Controller 1.1

7.4.2 Scenes - Loading and Saving

Previously Stored Settings

Load Scene - Accessing Previously Stored Settings

To load previously created and stored scenes, press

the SCENE key and then the

keys to select the

menu option Load Scene, if not already selected.

Press the ENTER key to go to the Load Scene

submenu and the

keys to choose the number

of the desired scene from 0 to 9. Press the ENTER

key to load the selected scene. The LCD will issue

a warning reading Different Speaker Series if the

selected scene uses speaker-speciﬁ c ﬁ lter sets other

than those used by the current scene. You must

conﬁ rm by pressing the ENTER key. A conﬁ rmation

prompt then appears in the LCD asking Are you

sure? Conﬁ rm again by pressing the ENTER key.

Scene X appears in the LCD indicating the given

scene has been loaded.

Save Scene - Storing Settings as a Scene

Once you have conﬁ gured the controller to suit the

venue, you can store the FIRNET’s current setup as

a scene. To do this, press the SCENE key and then

the

keys to choose the menu option Save

Scene (press the

key once). Press the ENTER key

to go to the Save Scene No submenu and the

arrow keys to choose a number from 0 to 9 for the

memory slot in which you wish to store the scene.

Press the ENTER key again to save the scene to the

chosen memory slot. A conﬁ rmation prompt then

appears in the LCD asking Are you sure? Conﬁ rm

again by pressing the ENTER key. Scene X appears

in the LCD indicating you have saved the scene.

7.4.3 Adjusting Levels

Adjusting Input Levels

Note: The input level refers to the change in the

internal signal processing (post A/D converter),

which affects the output levels (or output level

indication pre D/A converter).

To adjust the signal levels at the FIRNET’s inputs,

press the LEVEL key and then the

keys to

select the menu option Input Level, if not already

selected. After pressing the ENTER key, use the

keys to select an audio input (Input A or

Input B) and the

keys to set the desired gain

for this input. Then press the ENTER key to conﬁ rm

and assign this level.

Adjusting Output Levels

To adjust signal levels at the FIRNET’s outputs,

press the LEVEL key and then the

keys to

select the menu option Output Level (press the

key once). After pressing the ENTER key, use the

arrow

keys to select an audio output (Output

A to Output D) and the

keys to set the desired

gain for this output. Then press the ENTER key to

conﬁ rm and assign this level.

7.4.4 Delay/Phase

Adjusting Input Delays

To adjust the delays at the FIRNET’s inputs, press

the DELAY/PHASE key and then the arrow up and

down keys to select the menu option Delay, if not

already selected. Press the ENTER key and then the

keys to select the menu option Input Delay, if

not already selected. After pressing the ENTER key,

use the

keys to select an audio input (Input

A or Input B) and the

keys to set the desired

delay within a range of 0 to 500 ms for this input.

Then press the ENTER key to conﬁ rm and assign

this delay setting

Adjusting Output Delays

To adjust the delays at the FIRNET’s outputs, press

the DELAY/PHASE key and then the

keys

to select the menu option Delay, if not already

selected. Press the ENTER key and then the

keys to select the menu option Output Delay (press

once). After pressing the ENTER key, use the

keys to select an audio output (Output A to

Output D) and the

keys to set the desired

delay within a range of 0 to 500 ms for this output.

Then press the ENTER key to conﬁ rm and assign

this delay setting.