200M Dual Wifi range extender Mobile terminal operating manual V1.
Mobile terminal operating manual Preparations Plug the device into a power outlet and the indicator will flash when the device is powered on. Mobile phone settings 1.The mobile phone searches for the Wi-Fi signal and connects to the signal of the name "wlan_repeater"(without quotes)(as shown in Figure 1). There is no password by default. 2.Open the mobile browser and enter "192.168.10.1" (without quotes).
Mobile terminal operating manual Figure 3 Note: Some mobile phones will have the WLAN assistant prompts (as shown in Figure 4), click "CONNECT", otherwise the settings will not be completed. This WLAN network has no Internet access.Connect anyway? CANCEL CONNECT Figure 4 3.
Mobile terminal operating manual ！ System Work mode Setting Password ！ 192.168.10.1/view/admin_wizar 1 Complete 192.168.10.1/view/admin_wizar System Work mode Setting admin Work mode Next Next Figure 6 ！ 192.168.10.1/view/admin_wizar ！ System Work mode Setting Complete Repeater Back Figure 5 1 1 Complete 192.168.10.1/view/admin_wizar 1 WiFi name: HonortekWifi Encryption: WPA-PSK2 WiFi password: WiFi name: HonortekWifi Encryption: WPA-PSK2 Exterded 2.4G: Exterded 2.
Mobile terminal operating manual 4.In the "Routing Network Signal List", click the Wi-Fi signal you want to relay, and enter the password of the original Wi-Fi signal in "Wi-Fi password" (as shown in Figure 9). Click the [Next] button in Figure 9, and then click the [save] button (as shown in Figure 10), the device will be applied and restarted(as shown in Figure 11). Wait for one minute after restarting. If the indicator light is steady blue, it means that the repeater has been successfully relayed.
Mobile terminal operating manual Note: After configuration, the device will reboot and the Wi-Fi name will become "xxxx_EXT2.4G"/"xxxx_EXT5G". (xxxx is the name of the original Wi-Fi signal, the password is the password of the original Wi-Fi signal). If the repeater works in "Repeater mode", and you want to use the LAN network interface of the repeater. you have to insert the network cable after the configuration is completed and the indicator light is steady blue. 5.
Mobile terminal operating manual Set the 2.4G wireless SSID in "Extended 2.4G", set the 5.8G wireless SSID in "Extended 5G", and set the wireless password in "Wi-Fi password" (as shown in Figure 15). 6.
Mobile terminal operating manual System System Work mode Setting Work mode Complete AP mode System Work mode Setting Work mode Password Exterded 5G: text Work mode WPA/WPA2 Mix Setting Complete System: text Encryption: Back Complete Exterded 2.4G: admin AP mode Next Wi-Fi Setup WiFi password: text 2.
Mobile terminal operating manual Setting Complete ！ ！ System Work mode 1 192.168.10.1/view/admin_wizar System Work mode Setting 1 Complete ！ 192.168.10.1/view/admin_wizar 192.168.10.1/view/admin_wizar System Work mode Setting 1 Complete System: Work mode Router mode Internet settings DHCP client DHCP client Exterded 2.4G: Back Next Static IP PPPoE Exterded 5G: Encryption: WPA/WPA2 Mix Password admin Work mode Router mode Wi-Fi Setup WiFi password: text 2.
Mobile terminal operating manual 2.After the setting is completed, the saving is unsuccessful, and the device prompts that there is no network? A:Some mobile phones have the assistant prompts (as shown in Figure 4), click "CONNECT", otherwise the settings will not be completed. If the save is not successful, you will need to reconnect Wi-Fi_REPEAPTER Wi-Fi and reset it. This WLAN network has no Internet access.Connect anyway? CANCEL CONNECT Figure 20 3.
Mobile terminal operating manual A: After the setting is completed, the device will take effect with the new configuration. The default factory configuration will no longer be used. Please connect the newly set Wi-Fi name signal.It is recommended that you change the Wi-Fi name of the repeater to the same Wi-Fi name and password as the wireless router. When your mobile phone switches back and forth between the Wi-Fi router and the repeater, the mobile Wi-Fi will not dropped and seamlessly switch Wi-Fi! 5.
Mobile terminal operating manual FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
