Phau Ntawv Qhia

ManualsBrandsHLOPHONE ManualsPredatorHOLOPHANE Predator Medium Floodlight Wet Location

Installation and

Maintenance

Manual

AFTER INSTALLATION DELIVER THIS

MANUAL TO OWNER

IM-62-E

GR421

1. INTRODUCTION

1.1 Product Description. The Predator floodlights have been

designed and tested in accordance with UL1572. These floodlights

are suitable for use in wet locations.

- The floodlight model size is referred in Figure 1.

- Major components of the floodlight are identified in Figure 1.

- The Predator floodlights have been designed to allow permanent

installation of the yoke or knuckle fitter or box mount and housing

while still providing easy maintenance and repair.

- The lamp, all electrical components, and the reflector can be

accessed by opening the door.

- Using a socket wrench, the door can be opened by loosening

captive door screws.

- All electrical components and the lens are contained on the door

and the door can be removed easily and without tools (once the

captive door screws are loosened).

Predator

Medium Floodlight

Wet Location

- Doors can be replaced as units and repaired in a shop under

protected conditions.

-The reflector located within the housing can be replaced as

needed. Different types of reflectors will provide different light

distributions.

1.2 Alternate Information Sources. If additional

questions arise relative to the Predator floodlight that this document

or your supplier cannot answer please refer them to:

Holophane, Field Service Department

P.O. Box 3004

Newark, OH 43058-3004

866-759-1577

2. INSTALLATION

2.1 Tools and Materials Required. The following tools

and materials are required during installation of the Predator

floodlight:

Table 1. Installation Tools and Materials

DESCRIPTION USE

3/8" hex head socket wrench Captive door screws

3/4" hex head wrench Yoke bolt

1/2" hex head wrench Box Mount

9/16 hex head socket wrench Knuckle fitter bolt and set screw

Pliers Cord grip (if applicable)

Torque wrench Captive door screws, set

(inch and foot lbs) screws and bolts

Wire nuts

2.2 Yoke Mount Installation.

2.2.1 Bolt the yoke to the mounting structure using either two 3/8"

bolts or one 1/2" grade 5 bolt. Tighten bolts securely (30-35 ft. lbs.

for 3/8" bolts or 50-60 ft. lbs. for 1/2" bolt). These bolts are not

provided.

2.2.2 Loosen the captive door screws attaching the door to the

housing. Open the door. See Figure 1.

2.2.3 Detach the power disconnect plug from the disconnect

receptacle in the housing.

2.2.4 If needed, remove the door by removing the cotter pin from

the hinge pin and sliding the door hinge pins out of the housing.

NOTE POWER CORD FITTING

The threaded hole in the back of the housing is tapped for 1/2-14

NPT.

2.2.5 Use UL approved watertight power cord fittings (not

provided) on all installations where fittings are required.

2.2.6 Remove clear protective cover and install watertight fitting.

Tighten securely.

2.2.7 Make all wiring connections in accordance with approved

wiring methods. Ensure that all supply wires and supply wire

connections are retained between the folds of the wire shield in the

housing.

2.2.8 If the door was removed as in 2.2.4 reinstalll the door by

sliding the door hinge pins into the housing. Insert the cotter pin

through the hinge pin.

WARNING-READ THESE INSTRUCTIONS

CAREFULLY BEFORE ATTEMPTING TO INSTALL OR

MAINTAIN THIS FIXTURE. WORK MUST BE DONE

BY QUALIFIED PERSONNEL.

WARNING-BE CERTAIN THAT ALL ELECTRICAL

POWER IS DISCONNECTED FROM THE FIXTURE

BEFORE INSTALLING OR MAINTAINING THE FIXTURE.

WARNING-FOLLOW LAMP MANUFACTURER'S

OPERATING AND MAINTENANCE INSTRUCTIONS.

IMPORTANT SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE WARNINGS MAY

RESULT IN DEATH, INJURY OR SIGNIFICANT

PROPERTY DAMAGE.

DISCONTINUED

Summary of content (5 pages)

PAGE 1
® AFTER INSTALLATION DELIVER THIS MANUAL TO OWNER - Doors can be replaced as units and repaired in a shop under protected conditions. -The reflector located within the housing can be replaced as needed. Different types of reflectors will provide different light distributions. IMPORTANT SAFETY INSTRUCTIONS WARNING-READ 1.2 Alternate Information Sources.
PAGE 2
TI NU ED Figure 1 W H D 16-7/8" 22-3/4" 10-1/2" Weight 46 lbs. GR420 Figure 2 2.2.9 DI SC ON Insert the door disconnect plug into the disconnect receptacle in the housing. 2.2.10 Securely install the proper lamp. 2.2.11 Close the door. Thread the captive door screws into the housing. Tighten the captive door screws to 55 in. lbs. torque. This is required for watertight door seal. 2.2.12 Aim the floodlight restricting mounting to + 90o from vertical lamp base down. 2.2.
PAGE 3
Aim the floodlight restricting mounting to + 90o from vertical lamp base down. 2.3.11 Tighten the 3/8" diameter knuckle fitter bolt securely (approx. 16 ft.lb. recommended). Tighten (4) 3/8 set screws to 16 ft. lbs. See Figure 2. 2.3.12 Energize the floodlight. Check its operation and for proper area illumination. Adjust the aiming point as needed but within the limits of the mounting restrictions. Figure 3 ED 2.3.10 2.4 Box Mount Installation. 2.4.
PAGE 4
3.3 Electrical Component Replacement. Electrical components mounted on the door can be replaced as follows: Figure 4 3.4.1 3.4.2 3.4.3 TI NU 3.4 Door Installation. Slide the door hinge pins into the housing. Insert the cotter pin through the hinge pin. Insert the door disconnect plug into the disconnect receptacle in the housing. 3.4.4 Check the condition of the door gasket and seal area on the housing. Ensure that no damage exists that could affect seal integrity. 3.4.
PAGE 5
When installed, the wire guard helps protect the tempered glass lens from damage. 4.3.1 4.3.2 Loosen the captive door screws. See Figure 6. Slide the mounting loops in the wire guard over all four screws. 4.3.3 Tighten captive door screws to 55 in. lbs. torque. This is required for watertight door seal. TI NU Figure 6 ED 4.3 Wire Guard Installation and Maintenance. DI SC ON GR424 5.