User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
3.6.2 Add beltpacks
When using FreeSpeak Edge on E-IPA-HX , each beltpack takes up a matrix port. Select the
number of beltpacks you require.
1. Navigate to Cards and Ports and select the E-IPA-HX Card slot.
2. Click +Port. The following screen appears.
Note: If you are adding more than one port, you can enter values in the Characters to Replace and
Seed value fields to automatically generate labels. For example if you enter Label 0 in the
Label field, and then enter 0 in the Characters to replace and Seed value fields, this will
automatically generate labels called Label 1, Label 2, Label 3 up to the specified number of
labels.
3. Click Add to add the ports, and then Close to exit the screen.
Note: The ports that are allocated to beltpacks can be thought of as a pool of ports that can be used
by any FreeSpeak beltpack. You only need to allocate for the number of beltpacks you intend
to have connected to the system at any one time. No allocation for spare beltpacks is needed.
When at least one beltpack has been allocated to the card, you will see a Beltpacks button
appears under Hardware. Click this button to configure beltpacks in the usual way.
(Registration and Roles).
3.7 Beltpack roaming between E-IPA-HX cards
FreeSpeak beltpacks (FS II and FS Edge) cannot roam reliably between E-IPA cards. If they do
you will lose audio. Therefore, if you have more than one E-IPA card, you must configure IP
Page 16