User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
3.8.2 Cabling the FreeSpeak Edge TCVR
Run Ethernet cable from one of the LAN connectors on the E-IPA card (default AES67
connector = LAN 3) to the FS Edge TCVR via a properly configured IP network port.
3.9 Adding transceivers to the matrix
When at least one beltpack has been allocated to the card, you will see a Transceivers button
appear under Hardware. Click this button to add and remove IP transceivers.
Two methods can be used for adding transceivers;
1. Online configuration (the Discovery method)
2. Offline configuration
Once connected, you can allocate static IP addresses to the transceiver if you wish.
3.9.1 Online configuration (the Discovery method)
Use Detect IP TCVR to find the transceivers on the network. The AES67 interface of the E-
IPA-HX card and the transceivers must be on the same network. The EHX software must be on
the same network as the E-IPA Admin port.
By default, the E-IPA-HX and the Edge transceiver are in DHCP mode.
Note: The Detect IP TCVR feature works if the matrix and the transceivers are not on the same
subnet. However, for audio connection between the transceiver and the card, the devices must
be on the same subnet.
Page 21