User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
Table of contents
1 Important Safety instructions 6
1.1 Safety symbols 7
2 Introduction to FreeSpeak Edge™ 8
2.1 FreeSpeak Edge 5 GHz 8
2.2 System capacity 9
3 Installing FreeSpeak Edge 10
3.1 Installing the FreeSpeak Edge transceiver 10
3.2 Clear-Com cable recommendations 12
3.3 Daisy-chain transceivers 13
3.4 Installing and removing an E-IPA-HX card 14
3.5 Adding an E-IPA-HX card to the software 14
3.6 Configuring the E-IPA-HX card for FreeSpeak Edge 15
3.7 Beltpack roaming between E-IPA-HX cards 16
3.8 Connecting the FreeSpeak Edge transceivers to a matrix 17
3.9 Adding transceivers to the matrix 21
3.10 Beltpack roles 27
3.11 Registering the beltpack to a matrix 29
3.12 Connect the beltpacks 31
3.13 Radio Frequency (RF) channel selection and power settings 31
3.14 De-register beltpacks from a system 32
4 Site survey features 34
4.1 Transceiver standalone mode 34
4.2 Local RF scan using a beltpack 35
5 RF channel selection 5 GHz 37
5.1 Radio Frequency (RF) channel selection and power settings 39
5.2 Channel selection 40
5.3 Channel re-use 41
5.4 Using Dynamic Frequency Selection (DFS) channels 43
5.5 Radar scanning in DFS channels 44
5.6 Transceiver - excluded channels 45
5.7 Wireless Regulatory Region (WRR) 46
5.8 Change RF channels on the Edge transceiver 47
6 Operating the Edge beltpack 49
6.1 Top controls and display 49
Page 3