User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
3.11.2 Over The Air (OTA) wireless registration (EHX)
If your beltpacks are not within easy reach of the PC hosting the EHXsoftware, you can
register them remotely as long as they are within range of an active and registered transceiver.
To do this you must:
1. Enable registration mode in EHX (10 minute window).
2. From the beltpack, use the menu to connect to the system and then register.
Note: The beltpack menu must be in advanced mode to use OTA registration. If your beltpack's role
has been menu-restricted, you must enter an Admin Pin to gain menu access to register the BP.
To enable this on your beltpack navigate to: Menu>Administration>Enable Advanced Menu.
You need the four digit system code, found in EHX System preferences to enable this (default:
4632). If your beltpack is already in advanced mode you will not see this menu option.
In the EHX software
1. Navigate to Hardware>Beltpacks (you must add at least one transceiver to an E-IPA port
before doing this).
2. Click Enable registration mode at the bottom of the screen.
Note: This will start a 10 minute timer to allow OTA registration through the connected
transceivers. OTA registration can be disabled at any time by clicking the Disable
Registration Mode button at the bottom of the screen.
Register the beltpack to the system
1. On the beltpack, press and hold the + and - button on either side of the front of the
beltpack to enter the menu system.
2. Using either the rotary keys or the + and - buttons navigate to: Menu>System>System
Connect.
3. Press the menu select key (D).
Note: If your beltpack is already registered to a system, you will be asked to confirm a
disconnect.
4. Navigate to the system you want to register to and press D to start the registration process.
5. Use key C to cancel a selection or move back up the menu tree.
Page 30