User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
6.2 Front controls 50
6.3 Beltpack bottom connectors 50
6.4 Beltpack batteries and power 50
6.5 Menu mode 52
6.6 Use/persist local settings (beltpacks) 52
6.7 Edge beltpack menu access 53
6.8 FreeSpeak Edge beltpack menus 55
7 Operating the Edge transceiver 70
7.1 IP rating (Protection Marking) 70
7.2 FreeSpeak Edge transceiver connector panel 71
7.3 Powering the transceiver 71
7.4 Edge transceiver status LEDs 72
7.5 Reset the transceiver to default 75
7.6 Port security settings 75
7.7 Network and synchronization 76
7.8 General network and switching rules 76
7.9 Spare parts 77
8 Upgrading FreeSpeak Edge 78
8.1 Upgrading FreeSpeak Edge transceivers 78
8.2 Upgrading FreeSpeak Edge beltpacks 79
9 Specifications 81
9.1 FreeSpeak Edge beltpack 81
9.2 FreeSpeak Edge transceiver 83
9.3 FreeSpeak Edge battery charger and battery 84
9.4 Transceiver models (regional variations) 84
9.5 Transmission method 85
9.6 Notice about specifications 85
10 Regulatory compliance 86
10.1 Part numbers and regulatory models 87
10.2 FCC notice 87
10.3 FCC/IC/EC RF exposure warning 88
10.4 Industry canada compliance statement 88
10.5 Korean notice 89
10.6 Japan notice 89
10.7 Australia compliance statement 89
10.8 New Zealand compliance statement 90
Page 4