User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
l Reset the channels in the EHX software. Navigate to:
Matrix>Hardware>Transceivers>Transceiver>Basic Options, change channel and Apply
Map to Matrix.
l Power cycle the transceiver (this can take up to 5 minutes)
l Reset the transceiver in the EHX software. Navigate to:
Matrix>Hardware>Transceivers>Transceiver and click the cog icon for transceiver
properties.
l Click the Reset button.
5.4.3 Fail-safe DFSchannel set up
Radar in both channels is unlikely to happen in normal scenarios. However, if you want a fail-
safe set up on your transceiver you should use one DFSchannel and one non-DFS channel.
5.5 Radar scanning in DFS channels
The Edge system selects DFS channels by default, as these channels are less likely to contain
traffic than the universal channels. When a DFS channel is selected, the system must carry out
a channel scan to make sure that it is clear of radar. A scan occurs whenever the transceiver is
going through it's connection sequence and also periodically while it is in use.
Radar scanning usually takes one minute per channel. You will see the status lights on the
transceiver flash blue when a channel scan is occurring. The LEDs will flash blue/purple or
blue/yellow if the device is starting up and acquiring PTP and sync lock at the same time. If
radar is detected in a channel while the transceiver is connected to the system, transmission
will drop into the backup channel. You will see a double red flash on the transceiver status
light when radar is detected in a channel.
Note: If you have not selected a backup channel, the transceiver will not transmit when radar is
detected.
Page 44