User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
Press and hold the mode button Mode Feature
Status LED 2 shows mode selection.
< 3 seconds 1 Clear mode selection
> 3 < 6 seconds 2
Identify me feature. LED 2 white for 1
second then color mix flashing
> 6 < 9 seconds 3 LED 2 green. No feature.
> 9 < 12 seconds 4 LED 2 yellow. No feature.
> 12 seconds 5
LED 2 red. Reset the transceiver to
default settings. The device will also
reboot.
7.5 Reset the transceiver to default
To reset the IP Transceiver to default:
1. Press and hold the Mode button for at least 12 seconds. When the transceiver status light
turns red the device will have entered reset mode and you can release the mode button.
This will reset the IP Transceiver and remove any stored diagnostics.
Note: Reset can take up to 5 minutes.
l The Admin and the audio (AES67) IP addresses are reset to DHCP
l Channel selection will be reset to the default
l You will need to reconnect the transceiver to the matrix as it will be removed from the
EHX configuration
7.6 Port security settings
The following port security settings apply for the IP Transceiver.
Note: All ports are closed by default, and the firewall is enabled.
Page 75