User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
8 Upgrading FreeSpeak Edge
This section tells you how to upgrade your transceiver and beltpacks.
8.1 Upgrading FreeSpeak Edge transceivers
You can upgrade the transceiver firmware by:
l Upgrading from the matrix (the file extension for the upgrade firmware is .ccf)
l Using a USB connection (the file extension for the upgrade firmware is .ccf)
8.1.1 Upgrading from the matrix
1. Right-click on the Frame in the Layout window, and then select Firmware > Update
Firmware. The Update Firmware Wizard appears.
2. Select Next. The following screen appears:
Note: For the Edge transceivers, the Auto/Promoted radio button is always set to Auto.
3. Select the Wireless radio button.
4. Select Next, and then browse to the upgrade file (.ccf) and select Open. The upgrade file is
loaded to the transceiver, and the transceiver restarts.
You can track the status of the download in the EHX Event Log.
8.1.2 Upgrading by USB connection
Place the *.ccf upgrade image onto a USB stick in a folder named
firmware_upgrade
located in
the root of the USB FAT32 file system.
Note: Make sure that there is only one upgrade image in the folder. If not, the incorrect image might
be upgraded.
Page 78