User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
The upgrade will begin automatically when you insert the USB stick.
Note: Both status LEDs will flash light blue once per second for 5 seconds on successful detection of
the upgrade file. Both status LEDs will light solid red if there is an error during the upgrade.
When upgrade is complete, both status LEDs will flash green.
8.2 Upgrading FreeSpeak Edge beltpacks
You can upgrade the FreeSpeak II beltpack firmware by:
l Using a USB connection (the upgrade file for USB has a .ccu extension).
l Using an Over The Air upgrade.
8.2.1 Upgrading by USB connection
1. Connect the beltpack to a USB port on the computer running the EHX software.
2. Select Tools > Apply Wireless Firmware Via USB.
3. Browse to the location of the upgrade file, and then select Update Firmware. The upgrade
file for USB has a .ccu extension.
The upgrade file is downloaded to the beltpack or transceiver.
Note: FreeSpeak Edge beltpacks must be upgraded individually.
8.2.2 Upgrading beltpack firmware by Over The Air Upgrade
Note: You must first upgrade the transceivers before upgrading the beltpacks.
Note: When enable OTA registration on the beltpack is on, upgrade is disabled. Upgrade is re-
enabled when registration is finished.
Note: FreeSpeak Edge beltpacks must be upgraded one by one.
Note: For OTA upgrade, the beltpack must be within 15- 20 meters (50 to 66 feet) of the
transceiver.
1. Right-click on the Frame in the Layout window, and then select Firmware > Update
Firmware. The Update Firmware Wizard appears.
Page 79