User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
9 Specifications
9.1 FreeSpeak Edge beltpack
Specification Value
Audio bandwidth 200 to 12 kHz
Mode of operations Full duplex on all routes
Beltpack frequency response 100 Hz to 12 kHz
Beltpack assignment-select buttons 2, used to edit beltpack menu options
Number of simultaneous full-duplex audio
paths
Up to 9
Level/talk controls
9 push buttons, 5 level controls (2 rotary and
2 button level controls, with 1 master level
control)
Frequency spectrum
5170 to 5875 MHz (20 MHz channels set by
country)
Output power
Adjustable from 1 to 24 dBm (maximum
output power is determined by selected
channel and country)
Modulation
Orthogonal Frequency-Division Modulation
(OFDM)
Headset connector
4-pin male, Clear-Com standard, options for
5-pin female and 7-pin male with PTT
Headphone impedance ≥32 ohm
Microphone type
Dynamic or electret, selectable in beltpack
menu
Headset limiter Selectable from beltpack menu
Battery 4400 mAh
Power 16 Wh
Typical voltage 3.6 V
Page 81