User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
9.2 FreeSpeak Edge transceiver
Specification Value
Beltpacks supported per transceiver 10 in one cellular zone
Frequency spectrum
5170 to 5875 (20MHz channels set by
country)
Transceiver transmission range Up to 450 m (ft.), line of sight indoors
Local powering
12VDC power supply or 5V (USB) or 48V
PoE
Modulation
Orthogonal Frequency-Division Modulation
(OFDM)
Output power
Adjustable from 1 to 24 dBm (maximum
output power is determined by selected
channel and country).
SFP module
1GB (1000Base), <250mA maximum current
draw
Connection to matrix RJ45
Mounting
Separate wall plate with various mounting
options
Mic stand mounts,
Camera spigot mounting hole
Hole for lanyard mounting
Environmental
IP54 water and dust resistance.
Operating: 0 to 45 degrees Celsius
Storage:-30 to 70 degrees Celsius
Humidity: 20 to 90% non-condensing
Dimensions
60 x 180 x 220 mm (dwh) (2.4 x 7.0 x 8.7
inches)
Weight Approx. 460g (16.1 oz)
Page 83