User's Guide
Table Of Contents
- 1 Important Safety instructions
- 2 Introduction to FreeSpeak Edge™
- 3 Installing FreeSpeak Edge
- 3.1 Installing the FreeSpeak Edge transceiver
- 3.2 Clear-Com cable recommendations
- 3.3 Daisy-chain transceivers
- 3.4 Installing and removing an E-IPA-HX card
- 3.5 Adding an E-IPA-HX card to the software
- 3.6 Configuring the E-IPA-HX card for FreeSpeak Edge
- 3.7 Beltpack roaming between E-IPA-HX cards
- 3.8 Connecting the FreeSpeak Edge transceivers to a matrix
- 3.9 Adding transceivers to the matrix
- 3.10 Beltpack roles
- 3.11 Registering the beltpack to a matrix
- 3.12 Connect the beltpacks
- 3.13 Radio Frequency (RF) channel selection and power settings
- 3.14 De-register beltpacks from a system
- 4 Site survey features
- 5 RF channel selection 5 GHz
- 5.1 Radio Frequency (RF) channel selection and power settings
- 5.2 Channel selection
- 5.3 Channel re-use
- 5.4 Using Dynamic Frequency Selection (DFS) channels
- 5.5 Radar scanning in DFS channels
- 5.6 Transceiver - excluded channels
- 5.7 Wireless Regulatory Region (WRR)
- 5.8 Change RF channels on the Edge transceiver
- 6 Operating the Edge beltpack
- 7 Operating the Edge transceiver
- 8 Upgrading FreeSpeak Edge
- 9 Specifications
- 10 Regulatory compliance
- 10.1 Part numbers and regulatory models
- 10.2 FCC notice
- 10.3 FCC/IC/EC RF exposure warning
- 10.4 Industry canada compliance statement
- 10.5 Korean notice
- 10.6 Japan notice
- 10.7 Australia compliance statement
- 10.8 New Zealand compliance statement
- 10.9 European Union (CE mark)
- 10.10 Waste Electrical and Electronic Equipment (WEEE)
- 10.11 General Battery Safety Instructions for Battery Models: BAT41, BAT50, BAT60, BAT70, BAT80
- 10.12 배터리 모델에 대한 일반 배터리 안전 지침 : BAT41, BAT50, BAT60, BAT70, BAT80
- 10.13 BAT41, BAT50, BAT60, BAT70, BAT80
FreeSpeak Edge | User Guide
128 must perform a 10 minutes radar scanning (also known as CAC - Channel Availability
Check) before becoming an operating channel.
10.10 Waste Electrical and Electronic Equipment (WEEE)
The European Union (EU) WEEE Directive (2012/19/EU) places an obligation on producers
(manufacturers, distributors and/or retailers) to take-back electronic products at the end of
their useful life. The WEEE Directive covers most Clear-Com products being sold into the EU
as of August 13, 2005. Manufacturers, distributors and retailers are obliged to finance the costs
of recovery from municipal collection points, reuse, and recycling of specified percentages per
the WEEE requirements.
10.10.1 Instructions for Disposal of WEEE by Users in the European Union
The symbol shown below is on the product or on its packaging which indicates that this
product was put on the market after August 13, 2005 and must not be disposed of with other
waste. Instead, it is the user’s responsibility to dispose of the user’s waste equipment by
handing it over to a designated collection point for the recycling of WEEE. The separate
collection and recycling of waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment for
recycling, please contact your local authority, your household waste disposal service or the
seller from whom you purchased the product.
10.11 General Battery Safety Instructions for Battery Models: BAT41,
BAT50, BAT60, BAT70, BAT80
BAT80 batteries are specifically designed only for use with product(s) offered by: HM
Electronics Inc. (HME) Clear-Com LLC, an HME Company
SAFETY PRECAUTIONS: To ensure the safety and reliability of your Battery, follow the
guidelines in this section.
Page 91