User guide

User Manual Charging CordSpeaker
1. Hook it up old-school.
2. The power cord goes here.
3. That light lets you know when
Bluetooth has the hook up.
4. Check out how much juice is in
the battery.
5. Turn the music up or down. (Wait,
why do you need to turn it down?)
6. Push it to play, push it
again to pause.
7. That’s the power button, press and
hold for 5 seconds to power on.
CHARGE
RED (when plugged in)
Charging
Flashing RED
Low Battery
Ready to Party
Light Off
Quick Flash BLUE
Pairing Mode
Slow Flash BLUE
Connected
RED Line-In Mode
What It Looks Like What it Means
2
1
7
6
4
3
5
5
USER GUIDE AND WARRANTY INFORMATION
HX-P140
©2014 HMDX. All Rights Reserved.
IB-HXP140
Register your speaker at www.hmdxaudio.com. Information like where
you bought it and how you’re using it is like gold for the people who make
these speakers. Do them a solid, will ya?
Por manual de instrucciones e información de garantía en español
visítenos en www.hmdxaudio.com.
The HMDX Hangtime has friends—like, lots of them. Check them all out at
www.hmdxaudio.com.
Setup is pretty easy, but we put a manual together just in case you need it.
It’s full of information and sarcasm—just like that English teacher you had
that crazy semester.
HEY. HAVE WE SEEN YOU HERE BEFORE?
PACKAGE CONTENTS
JUST CHARGE IT
BLUETOOTH
®
CONNECTION: IT’S A SETUP
ALLOW US TO SHED SOME LIGHT
HOOKING UP OLD SCHOOL AUDIO, JACK
CONTROL YOUR DESTINY...
OR AT LEAST YOUR SPEAKER
Charging the speaker is so easy you’ve probably
figured it out by now, but just in case, you’ve got
two options: your computer or a wall outlet.
Now go get ready for an epic night while your speaker does too.
It needs about 3 hours of me time for 4 hours of party time.
1. The cord that came with the speaker —
the one with the USB on one end and
the Micro USB on the other — will
work with your computer.
2. If you want to use the wall outlet, you’ll
need to pick up a power cord with a
Micro USB the next time you’re at the
store or use any USB AC adaptor,
including the one for your cell.
Like any amazing couple, this one starts with a connection—one between
your device and the speaker’s Bluetooth.
Here’s how it works:
1. We know you’re probably going to think, “derp” with this one, but we
have to say it: Make sure the smartphone, tablet or computer you want
to hook up to the speaker has Bluetooth. (There. We got that out of the
way.)
2. Turn on the speaker and look for the little blinking light.
3. Do whatever your device needs you to do on its end. (We don’t know
what you’re using. We’re not spies.)
4. Look for HMDX Hangtime in your device’s Bluetooth list or click
YES—whatever pops up on your device—and BAM! you’re
connected.
5. Now hit PLAY on your speaker and crank it up—or down if you’re
lame.
You’re probably only going to have to do this once, unless your device
goes through a major I-just-dropped-it-in-the-pool kind of reboot. The
device and Bluetooth will find each other every time just as long as the
speaker is set to Bluetooth and your device’s Bluetooth is, you
know—on.
If you’re connecting to a computer, you may have some extra steps on
that end. You’ll have to get that information from the computer company.
Depending on your device you may be prompted to enter a pairing code.
If prompted, enter “0000” as the code.
Press and hold PLAY/PAUSE for 5 seconds to activate pairing mode.
Note: If you turn on your Hangtime but haven’t started the party, it will
automatically power off after 2 minutes of unpaired inactivity.
1. Plug one end of the cord into the speaker and the other into the
headphone jack on your device.
2. Turn on the speaker.
3. Hit PLAY on your device and crank it up—or down if you’re lame.
You’ll have to play and pause the music from your device, not your
speaker. No problem. You’re there anyway, right?