3-D Schrittzähler mit drahtloser Datenübertragung D45420-08-01-20_R1_13/09/2013 Kurzanleitung Lesen Sie bitte diese Anleitung vor der ersten Inbetriebnahme sorgfältig durch. HMM Diagnostics GmbH D-69221 Dossenheim, Germany www.hmm.
Vor dem ersten Gebrauch 1. Entfernen der Batterielasche Um das Gerät anzuschalten, muss die Lasche an der Seite des Gerätes entfernt werden (Abb. 1). Achten Sie vor herausziehen der Lasche darauf, dass das Gateway angeschaltet ist. Bitte die Lasche vorsichtig herausziehen. Nachdem Sie die Lasche entfernt haben, schaltet sich das Gerät ein. Die drei LED‘s leuchten 5 Sekunden schnell hintereinander auf. Daraufhin fangen diese an zu blinken.
DEUTSCH Schieben Sie das dünnere Ende der Schnur durch die zwei kleinen Ösen auf der Seite des Gerätes (Abb. 2). Drücken Sie die Schnur dazu so eng wie möglich zusammen - dies erleichtert das Durchschieben (Abb. 3). Danach schieben Sie das dickere Ende der Schnur durch die Schlaufe am dünneren Ende und ziehen die Schnur so lange durch, bis die Schlaufe fest sitzt (Abb. 4). Abb. 2 Abb. 4 Abb. 3 3.
in den Deckel ein. Danach legen Sie den Deckel wieder in das Gerät ein und schließen diesen durch drehen des Deckels mit einer Münze. Abb.
DEUTSCH Europäisches Gesetz am 13. Februar 2003 in Kraft trat, führte zu einer umfassenden Änderung bei der Enstorgung ausgedienter Elektrogeräte. Der vornehmliche Zweck dieser Direktive ist die Vermeidung von Elektroschrott (WEEE) bei gleichzeitiger Förderung der Wiederverwendung, des Recyclings und anderer Formen der Wiederaufbereitung, um Müll zu reduzieren. Das WEEE-Logo auf dem Produkt und auf der Verpackung weist darauf hin, dass das Produkt nicht im normalen Hausmüll entsorgt werden darf.
Garantie HMM Diagnostics GmbH stellt an seine Produkte hohe Qualitätsanforderungen. Aus diesem Grunde gewährt HMM Diagnostics GmbH beim Kauf dieses smartLAB® Produktes 2 Jahre Garantie. Sie können die Garantiezeit um 3 auf insgesamt 5 Jahre kostenlos verlängern, indem Sie Ihr Produkt bei HMM Diagnostics GmbH registrieren lassen. Bitte registrieren Sie sich Online unter folgender Seite: www.hmm.info/registrierung Verschleißteile, Batterie u.ä. unterfallen nicht der Garantie.
ENGLISH 3-D Step-counter with wireless data transfer Quick Start Instruction Please read this instruction thoroughly before first using this device HMM Diagnostics GmbH D-69221 Dossenheim, Germany www.hmm.
Before the first use 1. Remove the battery lash To turn on the device, you need to remove the lash on the side of the device (pict 1). Please make sure that your gateway is turned on. Please remove the battery lash carefully. After removal the device will turn on. The three LEDs will light up after each other several times for 5 seconds. Then the LEDs will start blinking which indicates that the device is trying to communicate with the gateway to set the device. 2.
pict 2 ENGLISH Push the thin end of the cord through the two tiny eyes at the back side of the device (pict 2). Pushing together the cord a little bit makes it easier to squeeze it through them (pic. 3). After that, push the thicker end of the cord through the loop on the thin end and pull it tight (pic. 4). pict 4 pict 3 3. Exchanging the Batteries To exchange the batterie you need to open the battery lid with a coin in direction of the arrow (pict 5).
pict 5 Regularity and Safety Notice Declaration of Conformity This product is compliant with the EC Directives: -1999/5/EC Safety Statement This product has been verified to conform to the safety certification in accordance with the specification of EN Standards: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 WEEE note The WEEE (Waste Electrical and Electronic Equipment) Directive, that came into effect as European law on 13th February 2003, led to a major change in the disposal of electrical equipment.
cessing to reduce waste. ENGLISH The WEEE logo on the product and the packaging indicates that it is not allowed to dispose of the product in the ordinary household waste. It is your responsibility to deliver all the disused electrical and electronic equipment to the respective collection points. A separate collection and proper recycling of electronic waste helps dealing economically with natural resources.
Hersteller/Manufacturer: HMM Diagnostics GmbH Friedrichstr. 89 D-69221 Dossenheim, Germany E-mail: info@hmm.info www.hmm.info Weitere Informationen zu den smartLAB® Produkten / More information on our smartLAB® products: www.smartlab.