ART INSTRUCTION MANUAL »+s with Replacement Parts SLICERS {INCLUDES MOTOR PARTS) 1612 ML-19515 1712 ML19525 1712R ML-19528 THIS MANUAL REPLACES AND SHOULD BE USED INSTEAD OF FORMS 128328, 128368 & 12887A FOR REPLACEMENT PARTS. MODEL 1612 SHOWN A product of HOBART CORPORATION TROY, OHIO 45374 FORM 14284 (Rev.
Installation, Operation and Care of MODELS 1612, 1712, & 1712R SLICERS SAVE THESE INSTRUCTIONS GENERAL The Hobart Models 1612, 1712, and 1712R Slicers are equipped with Hobart-built motors and are available for single phase electrical service.
ASSEMBLY Model 1612 After removing the slicer from its shipping base, loosen the thumb screw on the knife sharpener, place it in its storage slot (Fig. 1), and tighten the thumb screw. The oil shipped in the container marked HAVOLINE #10 and the can of Chevron Poly FM #0 grease are for machine lubrication; refer to the MAINTENANCE section of this manual for instructions on their use. KNIFE SHARPEN STORAGE POSITION | Pr18806-1 Fig. 1 Fig.
OPERATION SAFETY SAFETY DEVICES INCORPORATED IN THIS SLIER MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SLICER 1S IN USE. The FRONT and BACK KNIFE GUARDS (Fig. 2) must be in position on their locating studs and secured with the thumb screws, The MEAT GRIP must be used when slicing short ends to keep your hands away from the knife. When the slicer is not running, the INDEX KNOB (Fig. 3) must be turned back below zero (fully clockwise).
CARRIAGE 7 SLICING — MODEL 1712 Pull the carriage ail the way toward you until it reaches its stop. With the meat grip out of the way, place the product to be sliced on the carriage tray (Fig. 6). Adjust the fence (Fig. 8) by loosening the thumb screw and sliding the fence so that it is close to the product but not pushing against #t. Tighten the thumb screw, Set the meat grip (Fig. 7) against the product and turn on the slicer by pooling the switch knob (Fig. 6).
Adjust the gauge plate to obtain the desired slice thickness by muting the index knob (Fig. 7). The numbers on the index knob do not indicate actual measurements but may be used for reference lo duplicate slice thicknesses. Using the carriage tray handle or meat grip handle (Fig. 7), push the carriage back and forth to slice. To operate the slicer automatically, make sure the speed selector knob (Fig. 8) is set in, pull the carriage to the and of its travel, lift the actuating lever (Fig.
MEAT GRIP . ;¢ HANDLE ; ADJUSTING SCREW PL-18816-1 Fig. 11 for manual slicing, push the carriage back and forth using either the carriage tray handier or the meat grip handle (Fig. 10). For automatic slicing, tum the adjusting screw (Fig. 11} until the front edge of the actuating block (Fig. 11} is at the setting which matches that of the index knob. For example, if the index knob is set on 2, align the actuating block with the number 2 groove on the slide bar.
To change to high speed, pull the speed selector knob out (when the carriage is at the operator end of its travel) and rest the notch in the speed selector on the sifter sleeve. Release the speed selector to shift back to low speed. To disengage the driving unit, push the locking clip (Fig. 12) when the carriage is nearing the operator end of its travel. Always eave the driving unit in low speed (knob pushed in) when the slicer Is not operating automatically.
Wash and rinse both sides of each knife guard. CAREFULLY wash and rinse both sides of the knife by wiping outward from the center. Never use steel pads to clean the knife. Carefully reassemble the back and front knife guards. The back knife guard must be assembled first DO NOT wash any slicer components in a dishwasher. MAINTENANCE KNIFE SHARPENING The Hobart cast stainless steel knife will provide long service in normal food store or commercial kitchen use.
Plug in the power cord and pull the switch knob to start the slicer. Slowly turn the index knob clockwise to grind the beveled (back) edge of the knife. Grind only until a burr appears on the front edge of the knife. Turn the slicer off and inspect for a burr on the front edge of the knife. Repeat grinding as necessary unit the knife edge is burred. When & burr appears, start the slicer and depress the plunger (Fig. 15) for three seconds to engage the truing wheel.
REPLACEMENT PARTS 1612/1712/1712R 11-12-13-14 PR 1712/1712R BASE UNIT ILLUS. PART PL:18416 NO. NAME OF PART AMT. 1 P70238 Cover Bearing Bracken SD249 Self-Tapping Acres #83 Cover Junction Box o 4 Self-Tapping Screw #8-32 ¥ 38" Pan Hd., Asy. {Incas. items 26,22 Cap Screw x 3/4” Hex Hd 7 Love Washer 5/16" Medium Foot cos 9 Anal 10 Mach, Resew Base & Name ¢ 166 Ha 11712y ., 13 C-123802-8 Base & Name Plate Says.
1612/1712/1712R REPLACEMENT PARTS MALTOSE MOTOR PARTS fulls, PART PLATAEA NO, NAME OF PART I Mach, Nut £8-32 He. e 2 EEL-T-6 Lock Washer #8 F goalkeeper 3 B-120048 Stud Sta tor Bracken Bearing . | 5 Rotor Says. Rotor Says. (50 Hz.) . 7 Mach. Nut #8-32 Hex . . 8 Washer . PN 9 B-113655 Retainer Sector . . 10 M-70422 Washer Bearing BB-15-41 Bull Bearing N.D. 993L04 . 12 D-65477-150-1 Sta tor A: 115 V.. 60 Hay 13 D-65477-150-2 Sta tor Says {200 D-65477-150-3 {230V, D65477-150-4 v (115 D-65477-150-8 V., 50 Hz.
REPLACEMENT PARTS 1612/1712/1712R ELECTRICAL UNIT ILLUS. PART PL-15691 NO. NAME OF PART AMT. 14 C-1223425 Lighted Knob Sty (LIS 1223426 Lighted Knob Says. (200/240 B-768302 Duse Insert £-123647 Insulator Switch i Card & Plug Says. (115 Cord & Plug Sty. (200240 Cord Says. (LEC) RR13 Retaining Ring (Use with items Washer (Use with item Strain Relief (Use with iem Mich. Screw #8-32 x 3/8” Lack Washer #8 Ext. Shake proof 1 9 BELITTLE-148-1 Switch (With Nuts). FE219 Si rain Relies ..
REPLACEMENT PARTS 1612/1712/1712R 1712R CARRIAGE TRAY UNIT ILLUS, PART PL-18415-1 NO. NAME OF PART AMT, 1 M-68042 Screw Truss Hd, “Mylok™ 2 M70345 Washer Handle Retaining 3 M-70344 ‘Washer Handle Tension 4 B70202 Handle Est Grip . 5 M-70387 Washer Handle & B-105077-2 Meat Grip Atm & Bfl:mng A y mel; tumult :7) . T M-75135 Bearing Meat Grip Arn . 8 M-70386 Washer C-108134-2 Meat Grip Says. (Indus. item "10) e 10 A-105098 Caver Mea an Pin M-70448 Thumb Screw Fence . .
1612/1712/1712R REPLACEMENT PARTS 1712/1712R GEAR CASE UNIT ILLUS, PART PL1B67T NO. NAME OF PART ARRAY-17 Retaining Ring . w721 Washer R-70259 Arm Says . Pivot Shaft Thrust . . Retaining Ring e Roller Engaging Shaft Engaging Mich . Ring Stop Retaining Stop Engaging Mich, Shaft Spring Engaging Mich Mach, Resew #10-24 ¥ 3/8" R Hd Cover Plate Connecting Rod . e Connecting Rod SAYS AMT.
REPLACEMENT PARTS 1612/1712/1712R Pl-B418° KNIFE SHARPENER UNIT {BOTTOM MOUNTED) ILLUS, PART PL1B418-1 NO. NAME OF PART AMT. 1 M-74833 Resew Retaining. M-73851 Wheel Grinding M-74900 Shaft Grinding Wheel . 4 B-124659 Carrier Grinding \’shed . 5 8-8-10 Mach. Screw #10-24 x 112" Rd, Hd & ES-2-18 Washer 7 WS34g Washer . 8 TARP Rollins ?/32 X 7116” 9 BA-2-1 Ballad” Dia 10 v-13199 Collar Thrust . 11 M-3404-7 Screw Retaining . . 12 M-13201 Wheel Truing M-83082 Shaft Truing Wheel 14 B-124658 Carrier Truing Wheel .
