INSTRUCTION M A N U A L w i t h Replacement Parts MODELS 5 1 0 and 5 1 2 MEAT SLICERS THE HOBART FORM 11416 (11-73) MANUFACTURING COMPANY, TROY.
510/512 INSTRUCTIONS Fig. 1 Instructions for Operation and Care of MODELS 510 A N D 512 MEAT SLICERS 1. INSTALLATION: When the machine is packed for shipment, the three rubber feet (6, Fig. 1) and the one helper foot (7, Fig. 1) are removed and sent along in a cloth bag. The feet can be readily reassembled. Install the helper foot to the end of its thread at the comer of the base as shown (7, Fig. 1. The helper foot does not touch the counter or table and prevents the slicer from tipping.
INSTRUCTIONS 5101512 2. THICKNESS O F SLICE: The knob or dial (4, Fig. 1) adjusts the thickness of the slices cut. The numbers on the dial indicate actual measurements in . l o " . For example when setting dial at .25, slice would be 114" thick. 3. SAFETY PRECAUTIONS: When not actually slicing, turn the slice adjustment knob clockwise as far as it will go. The gage plate will cover the edge of the cutting knife and guard it. 4.
6.2 Remove the camage (section 7) and set the slice adjusting dial at 50. 6.3 Remove the sharpener from its storage place. 6.4 Unscrew the thumb screw on the sharpener until the sharpener slips upward into the slot (8, Fig. 1) at the bottom of the gage plate. Push the sharpener firmly upward with the right hand t o remove any rocking tendency. Tighten the thumb screw with the left hand. 6.5 Start the motor. 6.6 Turn the slice adjusting knob (2, Fig. 4) slowly t o the right.
INSTRUCTIONS 5101512 6.1 1 Stop the motor, remove the sharpener, turn the slice adjusting dial back t o zero, and return the sharpener t o its place on the inside of the side plate. 6.1 2 After sharpening; the slicer should again be cleaned t o remove any dust, o r dirt as a direct result of sharpening. NOTE: The adjustments on the sharpening unit are factory-set for best operation on the machine. 7.
510l512 REPLACEMENT PARTS BASE UNIT
REPLACEMENT PARTS 5 1 0 1 5 1 2 BASE UNIT PART NO. B-114297 FE-8-14 A-69375-1 B-114584-1 B-1145 84-3 C-111141 SD14-21 B-76911 M-18682 E-114219 Dl 14452 SD24-1 D-114236 --- M-7 04 12 NAME O F PART Knob - Locking ............................................ Strain Relief (900) ............................................ Cord & Plug Assy. (3 Cond. under 150 V.) ............................ Pilot Light (with nut) (115 V.) (Incls. item #5) ........................ Push Nut (Pilot Light) ...................
5101512 REPLACEMENT PARTS CARRIAGE UNIT
REPLACEMENT P A R T S 5 1 0 1 5 1 2 CARRIAGE UNIT ILLUS. PART PL-11928 NO. 1 2 *3 4 5 6 *7 8 *9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 SC-14-45 Dl13838 Dl13839 M-75135 B-113836. B-113984-2 B-113984-1 E-113985 E-113989 SC-15-20 E-113874 SC-64-15 A-107364 C-108197-5 SD24-48 B-111120 V-21046-1 M-20622 B-76912 M-83416 M-86260 C-114252 SD-24-47 E-76895 BB-5-5 WS-21-18 E-113987 *E-113992 E-114091 NAME OF PART AMT. Mach, Screw - #8-32 x 318" Flat Hd --- ............................. -- ..........
5101512 REPLACEMENT PARTS KNIFE UNIT
REPLACEMENT PARTS 5101512 KNIFE UNIT ILLUS. PART PL-11929 NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 *15 16 17 18 *19 20 21 *22 23 24 RP-2-25 C-114190 RR-7-22 SL-3-6 C-114189 El11152 B-114137 SD24-45 C-114603-1 R-12430-47 B-111152 El14141 El11154 E-109749 Dl11108 SC-22-18 B-114289 E-113825 E-113829 B-109756 (2-114527-2 C-114527-1 C-114603-1 SD24-46 C-114277 N A M E O F PART Retaining Ring .............................................. Washer - Wavy Spring ..........................................
5101512 REPLACEMENT PARTS GAGE PLATE A N D INDEXING MECH.
REPLACEMENT PARTS 5101512 GAGE PLATE AND INDEXING MECH. ILLUS. PART PL-11930 NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 *29 30 31 B-111117 B-113903 B-111116 B-113906 B-114146 SC-93-25 B-114114 B-113994 B-114122 B-109762 B-109767 SD24-49 C-114238 SC-23-49 C-114214 C-114212 B-114213 RP-2-40 SC-12-49 M-88887 M-88298 SC-63-14 B-111144 B-114101 B-109770 RP-2-40 B-114107 Dl14067 Dl14068 B-114112 SC-41-10 B-114103 NAME O F PART Rod - Gage Plate Slide .......................
510/512 REPLACEMENT PARTS ELECTRICAL UNIT PART NO. B-76893 B-877 11 -1 29-1 B-76913 C-114243 B-114267 RP-4-26 B-114261 NS-17-3 C-114580 WL-7-12 SD-24-1 SD-24-1 B-76914 NAME OF PART Knob Assy. ................................................. Lock Washer - # l o Ext. Shakeproof ................................. ..................... Self-Tapping Screw - #lo-24 x 318" Pan Hd. "Taptite" Self-Tapping Screw - #lo-24 x 318" Pan Hd. '"Taptite" ..................... Clip - Cable . . . . . . . . . . . . . . . .
REPLACEMENT PARTS 5101512 . KNIFE SHARPENER UNIT ILLUS. PART PL-11932 NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 M-74833 M-73851 M-74900 P-22670 WS-2-18 sc-8-10 WS-3-40 BA-2-1 V-13199 PG3-7 M-72801 M-69585-1 M-83089 M-73974 WS-2-18 BA-2-1 WS-4-39 M-70313 SC-8-10 WS-2-18 M-73975 M-83092 M-13201 hI-3404-7 B-109702 R-74023 M-73979 M-74007 NAME OF PART Screw - Retaining ............................................ Wheel -Grinding ............................................
5101512 INSTALLATION INSTALLA'TION D I A G R A M F O R M 11416 N O V . 1973 P R I N T E D I N U.S.A.