User's Manual

ManualsBrandsHobart ManualsWater SystemHobart Corp. Water System WS-C206

WS-C206/WS-C208 Hobart

Compact Water Softener

Installation Instructions

WS-C206

WS-C208

- NOTICE -

This Manual is prepared for the use of trained Hobart Service

Technicians and should not be used by those not properly

qualified.

This manual is not intended to be all encompassing. If you have

not attended a Hobart Service School for this product, you should

read, in its entirety, the repair procedure you wish to perform to

determine if you have the necessary tools, instruments and skills

required to perform the procedure. Procedures for which you do

not have the necessary tools, instruments and skills should be

performed by a trained Hobart Service Technician.

The reproduction, transfer, sale or other use of this Manual,

without the express written consent of Hobart, is prohibited.

This manual has been provided to you by ITW Food Equipment

Group LLC ("ITW FEG") without charge and remains the property

of ITW FEG, and by accepting this manual you agree that you will

return it to ITW FEG promptly upon its request for such return at

any time in the future.

SERVICE MANUAL

A product of Hobart Service 701 S. Ridge Ave Troy, OH 45374

F25311 Rev. A (0913)

Summary of content (10 pages)

PAGE 1
SERVICE MANUAL WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions WS-C206 WS-C208 - NOTICE This Manual is prepared for the use of trained Hobart Service Technicians and should not be used by those not properly qualified. This manual is not intended to be all encompassing.
PAGE 2
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions TABLE OF CONTENTS INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION WS-C206/WS-C208 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 DISC REPLACEMENT . . . . . . . . . . . . . . . . . . .
PAGE 3
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions - INSTALLATION INSTALLATION INSTALLATION WS-C206/WS-C208 NOTE: If installing a WS-208 install wheel kit. WSC206 already has wheels installed. 5. Disconnect the electrical power to the machine and follow lockout / tagout procedures. 1. Locate water supply line and appropriate drains for softener installation. 2. Install by-pass valving. Locate brass in/out adapters, 4 O-rings, and silicone seal lube. Fig. 3 6.
PAGE 4
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions - INSTALLATION Fig. 8 Fig. 5 8. Install one O-Ring into each groove of the brass adapter. 11. Install the brass adapters into the in/out ports and secure by reinstalling the bracket and pin. Fig. 6 9. Fig. 9 Apply a small amount of seal lube evenly onto each O-ring. 12. The female end of the connector hoses is designed to thread onto 3/4" pipe thread.
PAGE 5
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions - INSTALLATION 14. Insert tubing provided into the overflow port on the back of the softener and run drain lower than the cabinet connection to provide a gravity drain in the event of a internal cabinet leak. Fig. 11 Fig. 10 15. Review the meter disc selection chart and the water analysis provided. If no water analysis is provided test the water supply. 16.
PAGE 6
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions - INSTALLATION Brine Valve Settings Unit Float Cup Height Brine Setting WS-C206 .5 lb. 5.25" WS-C206 1.0 lb. 6.25" WS-C208 1.0 lb 5.25" WS-C208 1.4 lb 5.75" 23. After the adjustments have been made to the float cup, reinstall brine valve into the cabinet. NOTE: Do not drop brine valve into drum. Dropping may lower float cup, resulting in an improper setting. 24. Add a clean grade of salt at this time.
PAGE 7
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions - DISC REPLACEMENT DISC REPLACEMENT DISC REPLACEMENT WS-C206/ WS-C208 1. Remove screws and cap cover from level one. Fig. 15 4. Remove meter drive pawl. Fig. 13 2. Remove balance piston. Fig. 16 5. Remove meter disc. Fig. 14 3. Remove balance piston o-ring and balance piston spring. Fig. 17 Page 7 of 10 F25311 Rev.
PAGE 8
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions - DISC REPLACEMENT 6. Install correct meter disc and reassemble in reverse order. NOTE: Make certain all components are correctly installed. NOTE: Be certain to start cap screws by hand rotating backwards until screw drops into thread then tighten. An alternating, crossing pattern should be used while tightening cap screws to ensure correct cap fit. F25311 Rev.
PAGE 9
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions - DISC SELECTION DISC SELECTION DISC SELECTION WS-C206/WS-C208 The amount of hardness removed (in compensated gpg) will be based on the amount of brine and the meter disc selected. 1. Test water supply for hardness and iron content. Use water analysis test kit available through Pro Products Inc. The recommended kit is #2401 Field Analysis Kit. To order test kit contact Pro Products at 800-285-9176 or visit www.ProProducts.com. 2.
PAGE 10
WS-C206/WS-C208 Hobart Compact Water Softener Installation Instructions - DISC SELECTION WS-208 Disc Selection Disc Number Compensated Hardness at 1.0 lb setting * Compensated Hardness at 1.4 lb setting * Gallons Between Regeneration Regeneration Gallons Per Minute @ 15 psig. 1 2 3 4 6 7 8 4 9 14 19 23 27 30 35 5 11 17 22 27 32 35 40 732 366 244 183 146 122 105 92 10.2 10.2 10.2 10.2 10.2 8.3 6.7 5.