Blender User Manual

ManualsBrandsHobart ManualsBlenderFP150

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

FORM 33530 Rev. A (3-98)

MODEL FP150 FOOD PROCESSOR

ML-104600

FP150 Food Processor

Summary of content (8 pages)

PAGE 1
I FP150 Food Processor N S T R U C T I O N S MODEL FP150 FOOD PROCESSOR ML-104600 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 33530 Rev.
PAGE 2
LOCKING SCREW CUTTING TOOL FEEDER/LID WRENCH PUSHER FEED TUBE PUSHER PLATE DICING GRID EJECTOR PLATE PUSHER PLATE SHAFT LOCKING KNOB PL-52142 FP150 Food Processor TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
Installation, Operation and Care of MODEL FP150 FOOD PROCESSOR SAVE THESE INSTRUCTIONS FOR FUTURE USE GENERAL The Model FP150 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicing vegetables, fruits or cheese. The compact unit is designed for ease of operation and quick cleaning. A wall rack and a wide range of slicer, shredder, and dicing plates are available options.
PAGE 4
Interlock switches prevent the machine from operating when the feed hopper is out of position or the pusher plate is raised above the feed hopper. If these features do not function as described, contact your local Hobart service office. During operation, when the pusher plate is fully raised above the feed hopper, the machine stops and allows the pusher plate to be rotated counterclockwise for loading. To continue operation, rotate the pusher plate clockwise until it is directly above the feed hopper.
PAGE 5
CUTTING TOOL GUIDE PL-52135 PL-52136 PL-52137 PL-52138 PL-52139 Crimping Slicer — 3/16" (4.5 MM) For ripple slicing of root vegetables. Fine Slicer (2 Blade) — 1/16" (1.5 MM) For slicing firm or fragile products. Also for use with 9/32" dicing plate. Makes very thin slices of pepperoni, mushrooms, cabbage, potatoes, cucumbers and radishes. Fine Slicer (1 Blade) — 5/32" (4 MM), 9/16" (14 MM), 1/8" (3 MM), 7/32" (6 MM), 3/8" (10 MM) Use is same as 2-blade fine slicer.
PAGE 6
USING THE FEED HOPPER After the pusher plate is raised, prepared products such as potatoes, carrots, onions, lettuce, cabbage, etc., can be placed in the large feed hopper. The feed hopper has one fixed and one detachable partition wall. For highest capacity and best cutting results, the detachable partition wall should be removed only when necessary because of product size. To remove the detachable partition wall, unscrew the two black knobs on the outside of the feed hopper.
PAGE 7
9. Replace the locking screw. 10. Place the feed hopper on the hinge pins and lower to normal position. Turn and lower the pusher plate. Replace the feed tube pusher. MAINTENANCE WARNING: TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE. Routinely inspect the machine to ensure that it is in proper working order. Plates must be clean, intact and sharp. Regularly lubricate the pusher plate shaft with a drop of mineral oil, NOT COOKING OIL.
PAGE 8
TROUBLESHOOTING FAULT Motor won't start. POSSIBLE CAUSE REMEDY A. Feed hopper not locked in correct position. Make sure feed hopper is locked correctly. B. Pusher plate raised. Turn pusher plate clockwise and lower it. C. Fuse or circuit interrupting power. Machine stops while operating and won't restart. Low output or bad cutting results. Scraping sounds. Cutting tool locked to shaft. FORM 33530 Rev. A (3-98) breaker Have electrician check circuit. A. See B and C above. B.