Security Label Applier Operator Manual Model SLA-1, SLA-2 SLA-2A SLA-3 ML-44180 ML-44197 ML-44192 701 S. RIDGE AVENUE TROY, OHIO 45374 937 332-3000 www.hobartcorp.com © HOBART 2006 F33995 (Rev.
Security Label Applier (SLA) SAVE THESE INSTRUCTIONS Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Security Label Applier The Security Label Applier (SLA) is designed to apply an Electronic Article Surveillance (EAS) label to a standard Ultima scale label. The SLA works in conjunction with an Ultima (with remote keypad) and an Ultima Wrapping System (UWS), Compact Label Applier (CLA) or Indexing Label Applier (ILA). As a label is printed and expelled from the Ultima Printer, the SLA attaches a security label to the adhesive side of the merchandising label.
Note If used with an HWS or NSW Semi Automatic System, the security label is automatically placed on the Ultima scale label. The Operator then hand applies the labels to the package. There are two types of security labels available. Depending on your store security system, you will either use the Checkpoint label (similar in size to the safe handling label) or the Sensormatic label (similar to what is used with audio CDs). Note For label ordering information, contact your security system provider.
1. At the Ultima Keypad, PRESS [SUPER MENU ON/OFF]. If applicable, enter your Secret ID. The Supervisor Menu displays. 2. PRESS [F5] to select Scale Setup Menu. 3. PRESS [F3] to select Labels Menu. 4. PRESS [F6] to select Security Labels. © HOBART 2006 Page 5 of 12 F33995 (Rev.
5. From the Security Labels screen, enter the minimum Unit Price and/or the minimum Total Price. A security label will be applied to any package with a Unit Price and/or Total Price that is the same as or higher than the amounts entered. If the Unit Price and Total Price are lower than the entered prices, the security label will not be applied. 6. PRESS [ESC] to return to the Start a Run screen. To set up the SLA to apply a label by PLU: 1. At the Ultima Keypad, PRESS [SUPER MENU ON/OFF].
3. Use the numeric keypad to enter PLU number in the Product number and PRESS [ENTER]. 4. PRESS [F2] to select Apply Security Label. 5. PRESS [ESC] to return to the Start a Run screen. Operating the SLA Once set up, the SLA runs with minimal operator intervention. The labels are automatically generated, combined and placed on the appropriate package. The SLA contains a label sensor to alert the operator when out of labels or when labels are not advancing.
Loading Labels The SLA contains a label sensor to alert the operator when out of labels or when labels are not advancing. When applicable, the message Out of Security Labels displays on the Ultima console and a beep sounds to alert the operator. Although, when out of security labels, the Ultima merchandising labels continue to print. You may also receive this message if the SLA is turned off, but you are still operating the Ultima printer.
© HOBART 2006 Fig 1 Fig 2 Fig 3 Fig 4 Page 9 of 12 F33995 (Rev.
Cleaning and Maintaining Maintain the SLA by regularly cleaning the paper dust from inside the unit. Clean the SLA exterior surfaces with a cloth and warm water/detergent solution. When cleaning, be sure to protect the unit from direct water entry. To clean the SLA: 1. Dampen a soft cloth with mild detergent and water. 2. Wipe the exterior surfaces. Note Remove any adhered labels with an alcohol soaked cloth. Do not use metal to scrape the labels or adhesive off of the unit.
SYMPTOMS POSSIBLE CAUSES/REMIDIES Multiple labels are issued followed by an audible beeping sound. 1. Verify labels threaded correctly. 2. Call local Hobart office. No label is issued followed by an audible beeping sound. 1. 2. 3. 4. Security label placement on Ultima label is incorrect. 1. Verify that dwell control lever is resting against the backing paper on the take-up spool. 2. Verify labels threaded correctly. 3. Call local Hobart office. © HOBART 2006 Page 11 of 12 Out of security labels.
© HOBART 2006 F33995 (Rev.