User's Manual

ManualsBrandsHobbi ManualsCamera & PhotoWi-Fi Camera Kodo FPV

CHARGING the FLIGHT BATTERY

Plug charger into USB port or AC adapter (DIDP1125 not included)

as shown and connect the battery. The red LED will flash slowly

while the battery is charging. The LED will be steady when the

battery is fully charged.

• NEVER leave the battery unattended while charging.

• DO NOT allow the USB port to power down while the charger

is connected to the battery.

• ALWAYS unplug the charger from the USB port and the

battery when charging is complete.

• The battery connector will only fit in one way.

SETUP

Your KODO FPV comes with a Power-On Fail-Safe. This ensures that

the motors will not start until the KODO has detected the controller.

1. Turn on the controller with the throttle

at its lowest position.

2. Connect the battery to the KODO

FPV and place it on a level surface.

Listen for two beeps. The red LED at

the back of the quadcopter will start

 ashing slowly.

3. Move the throttle to its highest position. Listen for a beep.

4. Move the throttle back to its lowest position. Listen for three

beeps.

The KODO FPV’s motors are now armed and the quad is ready to

 y. The red LED on the KODO FPV will become steady.

READ THESEREAD THESE

INSTRUCTIONSINSTRUCTIONS

BEFOREBEFORE FLYING ! FLYING !

• Do not mix old and new batteries.

• Do not mix alkaline, standard, or

rechargeable batteries.

CONTROLLER

Push down on the left stick to

change the sensitivity

of the controls.

SENSITIVITY ADJUSTMENT

Lowest (Default)

Moderate

Maximum

Remove the screw on

the battery compartment

cover. Take the cover off

and insert 4 AAA batteries.

Replace cover, securing

with the screw.

Video

Button

Elevator

Trim

Throttle/Rudder

Stick

Rudder

Trim

ON/OFF Aileron

Trim

Aileron/Elevator

Stick

Throttle

Trim

Phone Holder

Picture

Button

™

KODO

™

Drone

Controller

FPV Headset

Screwdriver

USB

Charger

Spare Blades

(2 black, 2 red)

Flight Battery

4 AAA Batteries

Summary of content (8 pages)

PAGE 1
™ READ THESE INSTRUCTIONS BEFORE FLYING ! FPV Headset Controller Spare Blades (2 black, 2 red) 4 AAA Batteries USB Charger KODO™ Drone Flight Battery Screwdriver CONTROLLER Picture Throttle Trim Button Phone Holder Elevator Trim SENSITIVITY ADJUSTMENT Video Button Push down on the left stick to change the sensitivity of the controls. Lowest (Default) Moderate Throttle/Rudder Rudder ON/OFF Stick Trim Aileron Trim Aileron/Elevator Stick Remove the screw on the battery compartment cover.
PAGE 2
HOW to FLY CORRECTING DRIFT It is normal for the KODO FPV to drift slightly. However, if it drifts in any direction consistently, press the trim button that is opposite the movement as many times as needed to eliminate the drift. D B B A C C A D A B D B C C FPV CAMERA D A Picture Button Video Button Press the picture button to capture a photo. Basic Flight Advance the throttle slowly until your KODO FPV rises into the air. Press the video button to start a video.
PAGE 3
APP CONTROLS VR HEADSET The VR Headset uses your smartphone to provide a more immersive image. The focus and the Interpupillary distance (IPD) can be adjusted. The headset also has a camera port that can be opened if you have an app that needs to overlay images onto the scene from the camera. Tap the FLY button to connect to the FPV camera. Tap the “?” button to view the help screens. The headset has a camera tray that must be removed before the smartphone can be installed.
PAGE 4
MOTOR REPLACEMENT Step 3 ● Set up a course. Keep it simple at first. When you can fly while maintaining your altitude, set up a course with gates or obstacles at different heights. The goals are to fly the entire course while maintaining the altitude and increase your speed around the course. BLADE GUARD REPLACEMENT 1. Carefully pry off the blade using a flat head screwdriver. NOTE: Do one corner at a time so you don’t accidentally mix up the blades. 1. Remove the rotor blade from the motor. 2.
PAGE 5
model. If not operated correctly, the model could possibly cause injury to you or spectators and damage to property. Do • not alter or modify the model, as doing so may result in an unsafe or unflyable model. You • must check the operation of the model before every flight to ensure that the model has remained structurally sound. CAUTION: Changes or modifications to this product not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment.
PAGE 6
ISEDC Radiation Exposure Statement: This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For Quadcopter:This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. Cet appareil est conforme aux limitesd'exposition de rayonnement RF ISEDC établiespour un environnement non contr?lé.
PAGE 7
ALSO AVAILABLE Instant FPV. Vusion 250 Extreme FPV Race Pack The revolutionary Vusion 250 Extreme FPV Race Pack blends innovation and convenience with the ultimate First Person View racing drone. It’s the first – and only – injection-molded RTF 250-size racing drone to come with all essential FPV equipment installed. Everything’s designed to work seamlessly together, for the ultimate flying experience! ● 100% complete and Ready-to-Fly FPV Race Pack – no soldering, assembly or kit-bashing required.