Instruction manual

®
Non Computerized Transmitter Setup
(DX4e and DX5e)
Transmitter
SAFE
mode
switch
Panic Recovery Switch
SAFE Flight
Modes Supported
Throttle, Aileron, Elevator and Rudder in Normal Position
DX4e
(2pos switch)
ACT/AUX
switch
Trainer Button 2 Pos Flight Mode
DX4e
(3pos switch)
CH 5
switch
Trainer Button 3 Pos Flight Mode
DX5e
(2pos switch)
CH 5
switch
Trainer Switch 2 Pos Flight Mode
DX5e
(3pos switch)
CH 5
switch
Trainer Switch 3 Pos Flight Mode
Computerized Transmitter Setup
(DX6i, DX6, DX7S, DX8, DX9, DX10t and DX18)
Start all transmitter programming with a blank model (do a model reset), then name the model.
Set Dual Rates to:
HIGH 100%
LOW 70%
DX6i
1. Go to the SETUP LIST MENU
2. Set MODELTYPE: ACRO
3. Set REVERSE: Gear Channel
4. Go to ADJUST LIST MENU
5. Set TRAVEL ADJ: Gear/Fmode (0)100%; Gear/Fmode (1) 40%
6. Set FLAPS: Norm 100; LAND 100
7. Set MIX 1: ACT; Gear Gear ACT, RATE D 0%; U + 100%, SW MIX, TRIM INH
Resulting in: The Gear and Mix switches operate the 3 SAFE modes
Gear 0; Mix 0 = Beginner Mode
Gear 1; Mix 0 = Intermediate Mode
Gear 1; Mix 1 = Experienced Mode
The Flap switch operates Panic Recovery:
Position 0=Off, Position 1=On. (not a momentary switch)
DX7S
DX8
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set SWITCH SELECT: Change all to INH then TRAINER: AUX1, FLAP: GEAR
4. Go to the FUNCTION LIST
5. Set SERVO SETUP: Reverse AUX1
Resulting in: Flap/Gyro Switch operates the 3 SAFE modes (0 beginner/1 inter-
mediate/2 experienced)
The Trainer/Bind button operates Panic Recovery
DX6
DX9
DX10t
DX18
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set CHANNEL ASSIGN:
click NEXT to go to Channel Input Confi g:
GEAR: B, AUX1: i (DX10t GEAR: A, AUX1: R-stick)
4. Go to the FUNCTION LIST
5. Set SERVO SETUP: Reverse AUX1
Resulting in:
Switch B (DX10t: A) operates the 3 SAFE modes (0 beginner/1
intermediate/2 experienced)
The Bind/I button (DX10t: R-stick) operates Panic Recovery
IMPORTANT: The included AR636 receiver has been
programmed for operation specifi cally in this aircraft.
The programming in this receiver cannot be changed
by the user.
To operate the SAFE system in this aircraft, set up
your optional DSM2/DSMX transmitter using the chart
below.
- SAFE Flight mode is selected using Channel 5
signal (high, middle, low)
- Panic Recovery mode is selected with Channel 6
signal (high, low)
IMPORTANT: A transmitter with a 2-position Channel
5 switch will only allow the use of position 0 or posi-
tion 2 fl ight modes. If possible (refer to your transmit-
ter manual), assign Channel 5 in your transmitter to a
3-position switch to operate all 3 fl ight modes.
Refer to your transmitter’s manual for more informa-
tion about transmitter setup.
Transmitter Setup
F4U Corsair SEN
12