H-King Savage Bobber 1000 mm 5ch ARF Version
FEATURES: - Skillfully hand-crafted construction - Factory-applied covering film - Crystal clear plastic windshield - Vacuum formed plastic engine cowling - Carbon wing joiner, and wing struts - Colorful factory-applied self adhesive decals - High-quality comprehensive hardware pack - Scale wheels with oversized tires - Pre-slotted hinge pockets - Wingspan: 1000mm - Length: 700 mm - All Up Weight w/Battery: 650g depending on set-up - Motor: 2826 1130 KV - Servos: 6 x 3~6g - Battery: 1000~1300mA
1 19 2 5 4 6 7 12 13 3 18 8 9 20 14 16 10 11 15 17 21 CONTENTS: 1. Fuselage 2. Cowling 3. Vertical stabilizer 4. Horizontal stabilizer 5. Landing gear 6. Main wheels 7. Tail wheel 8. Fiber sheets (Control horns and mounting straps) 9. Servo mount spacers 10. 3mm x 25mm carbon fiber wing joiner 11. Pushrods 12. Servo mounting blocks 13. Wing mounting metal fittings 14. 1.5mm x 6 mm self-tapping screws 15. Wheel collars & pushrod stoppers 16. 8 mm x 265 mm carbon fiber wing joiner 17.
LANDING GEAR INSTALLATION: Remove the landing gear mounting strap from the supplied fiber sheet and find the M1.5x6 tmm selftapping screws in one of the accessory bags. Attach the wire landing gear to the fuselage using the self-tapping screws to secure it in place. Note: The set of wing strut joiners on the landing gear should be positioned towards the rear of the fuselage. WHEEL INSTALLATION: Install and secure the set of wheels by using the supplied wheel collars as shown.
HORIZONTAL STABILIZER AND VERTICAL RUDDER INSTALLATION: Firstly, dry fit and tape the horizontal tail onto the fuselage. secondly, align the stabilizer accordingly to ensure it is true and square to the fuselage. Then use a hobby knife and gently cut through the covering. Finally, peel off the covering and it’s ready for installation. Apply CA glue to the bare wood area you have exposed on the stabilizer and attach it to the rear of the fuselage.
Dry fit the rudder/fin assembly onto the horizontal stabilizer, ensure they are perpendicular to each other. Once you are satisfied with the fit, apply CA glue to the fin to secure it in place. Then install hinges half way into the pre-slotted hinge pockets in the rudder by applying a small amount of thin CA glue as shown, wait until it has throughly dried. Install the rudder to the fin, and slide the hinges into the hinge pockets on the fin.
AILERON SERVO & FLAP INSTALLATION: First, make a cut in the covering at the servo horn opening and trim the area neatly on the servo mounting plate with a hobby knife as shown. Secondly, position the servo in the center on the servo mounting plate, and glue the supplied wooden mounting blocks onto the mounting plate as shown. Ensure the servo horn sits right in the middle of the opening without any interference of the servo arms movement whilst the glue dries.
CONTROL HORNS AND PUSHROD LINKAGES INSTALLATION: Apply medium CA glue to the surface control horn and stick it into the slot as shown. Once the glue has set, install a supplied pushrod stopper onto the control horn. In order to get the best mechanical linkage setup, first of all ensure that the servo control horn is perpendicular to the servo case. Then connect the pushrod to the servo control horn and connect the pushrod stopper as shown.
FLAP SERVO INSTALLATION: Repeat the above steps for the flap servo installation. COCKPIT WINDSHIELD INSTALLATION: Install the factory pre-cut PVC windshield onto the fuselage cockpit area. Use masking tape to hold the windshield in place on the cockpit frame as shown in the pictures, do this on both sides. Ensure the PVC sheet is evenly positioned on the turtle deck in front of the cockpit. Adjust the windshield as necessary to achieve the best fit.
Then tape the other end to the rear part of the wing saddle. Once you are satisfied with the overall fit and placement of the PVC windshield, secure it in place using the supplied M1.5x6 mm self-tapping screws. ELEVATOR AND RUDDER SERVO INSTALLATION: Before installing the elevator servo, feed the servo lead through the plastic tube from the tail servo mount at the rear of the fuselage to the main radio compartment.
Connect the pushrod to the servo control horn and connect the pushrod stopper as shown. Get a piece of masking tape to hold the control surface straight and level, then tighten the grub screw on the stopper with a hex key. Apply a small spot of thread lock glue where necessary. Trim off the excess pushrod length with a set of wire cutters. Repeat the above steps for the rudder servo pushrod linkage installation.
First of all, install the X mount to the motor. Then position it to achieve the correct motor offset, thrust line as indicated by the red arrow on former F9. Secure the motor in place by using the supplied M3 x10 mm self-tapping screws. The firewall on the Savage Bobber has a built-in 3 degrees of right thrust. This is a good starting point for the recommended propeller size.
MAIN WING INSTALLATION: Insert the supplied 8 mm x 265 mm and 3 mm x 85 mm carbon fiber wing joiner onto the fuselage wing saddle as shown. Install the left wing onto the fuselage.
We have supplied a set of carbon fiber wing struts. Identify the longer one for the rear wing strut and the shorter one for the front. Two additional metal fittings are also required for the installation. Install the carbon fiber wing strut (rear) to “A” and insert the metal fitting onto the other end. Then insert it into the pre-drilled hole on the underside of the wing, ensure the metal fitting is fully inserted. You may have to use a pair of pliers to make some adjustments to achieve a proper fit.
C OF G AND CONTROL SURFACE THROW SETTING INFORMATION: CONTROL DIRECTIONS TESTS: Stick backward Stick forward Stick right View from the nose. Stick left View from the nose. Stick right View from the nose. Stick left View from the nose.
MODEL FLYING PRECAUTIONS: YOUR NIGHT TUNDRA COMES WITH SEVERAL FEATURES • Select your flying area carefully. Always choose an open space that is clear and not obstructed by trees, poles, pylons, and buildings etc. Also ensure you are away from people and crowded areas. Avoid flying in areas with roads, near water, or within close proximity to full size air traffic.
RECOMMEND BATTERY: Turnigy 1000mAh 3S 30C Lipo Pack SKU: T1000.3S.30 Turnigy Nano-Tech 1000mAh 3S 40C Lipo Pack w/XT60 SKU: 9210000274-0 Turnigy Nano-Tech Plus 1000mAh 3S 70C Lipo Pack w/ XT60 SKU: 9210000261-0 Turnigy Graphene Panther 1000mAh 3S 75C Battery Pack SKU: 9067000361-0 Turnigy nano-tech 1000mah 3S 25~50C Lipo Pack SKU: N1000.3S.
UK REP APEX CE SPECIALISTS LIMITED M1 4HT, UK APEX CE SPECIALISTS LIMITED EC REP
