User Manual

ManualsBrandsHobbyKing ManualsHobbyHobbyKing® ™ Brushless Car ESC 30A w/ Reverse

Manual of QUIK Series Sensorless Brushless Motor Speed Controller

User Manual of Quik Series ESC for Car

V2.1

Features

 Full protection feature including low voltage, over-heat, throttle signal lost, startup protection and self-check.

 Compatible with sensorless brushless motor.

 Excellent startup performance, great throttle linear and quick throttle response.

 Support highest motor speed 240,000RPM (2 poles), 80,000RPM (6 poles) and 40,000 RPM (12 poles).

 The parameters of ESC can be configured via program card or the key on ESC.

 The low-voltage threshold and start-up power can be programmed quantified and precisely by program card.

 System can automatically detect throttle neutral point and neutral range is adjustable.

 Three work modes can match different requirement, 4 steps of maximum reverse force adjustment.

 3 steps of maximum brake force adjustment, 5 steps of drag brake force adjustment, 4 steps of initial brake force adjustment.

 Support 1 cell operation (min voltage: 3V, only available for XC-6A and XC-10A).

 QUIK-60A 80A 100A have connector for light .User can assemble car light.(refer to the wiring diagram).

Specification

Battery Cell

P/N

Continuous

current

Li-XX Ni-H

Dimension

(mm)

L×W×H

Weight

BEC

Program

card

Program

key

XC-6A 6A 1-2 3-8 12 x 20 x 5 4 1A/5V(linear) Yes NO

XC-10A 10A 1-2 3-8 22 x 17 x 7 8 1A/5V(linear) Yes NO

Quik-30A

30A 2-3 4-9 45x32x20 51 2A/5V(linear) Yes Yes

Quik -45A

45A 2-3 4-12 45x32x20 60 2A/5V(linear) Yes Yes

Quik -60A

60A 2-4 4-15 47x41x29 82 3A/5V(switch) Yes Yes

Quik -80A

80A 2-4 4-15 47x41x29 89 3A/5V(switch) Yes Yes

Quik -100A

100A 2-4 4-15 47x41x29 95 3A/5V(switch) Yes Yes

XC-150A 150A 2-6 5-18 96x55x21 180 NO Yes NO

XC-120A-HV

120A 2-10 5-30 96x55x21 180 NO Yes NO

Note: For XC-150A and XC-120A-HV, an UBEC or individual battery pack should be required to power the receiver and servos.

Using ESC

Normal Startup Procedure

Move throttle stick to the neutral position Switch on the transmitter Connect battery pack to ESC System detects the

neutral throttle signal, makes a long “beep-” sound System detects battery voltage and makes several short “beep-” sounds, which

denotes the number of battery cells when self-test is finished ♪ 1 2 3 tone should be emitted ready for start.

Setting Throttle Range (Throttle range should be setup when a new transmitter is being used)

 QUIK series ( “ SET ” KEY is used )

Switch off the ESC Switch on the transmitter Press and hold the “ SET ” KEY Switch on the ESC Push the

throttle stick to the top point of forward within two seconds Wait for one second System detects the Max throttle signal, and

makes two “beep-” sounds, which denotes that Max throttle has been confirmed and saved Pull the throttle stick to the top point of

backward System detects the Min throttle signal, makes two “beep-” sounds, which denotes that Min throttle has been confirmed and

saved Release the “ SET ” KEY Setting is finished.

 XC series (no “ SET ” KEY )

Push the throttle stick to the top point of forward

Switch on the transmitter Connect battery pack to ESC

Wait for 2

seconds System detects the Max throttle signal, and makes two “beep-” sounds, which denotes that Max throttle has been confirmed

and saved Pull the throttle stick to the top point of backward System detects the Min throttle signal, makes two “beep-” sounds,

Summary of content (4 pages)

PAGE 1
Manual of QUIK Series Sensorless Brushless Motor Speed Controller User Manual of Quik Series ESC for Car V2.1 Features Full protection feature including low voltage, over-heat, throttle signal lost, startup protection and self-check. Compatible with sensorless brushless motor. Excellent startup performance, great throttle linear and quick throttle response. Support highest motor speed 240,000RPM (2 poles), 80,000RPM (6 poles) and 40,000 RPM (12 poles).
PAGE 2
Manual of QUIK Series Sensorless Brushless Motor Speed Controller → Setting is finished. After setting is finished ,push the throttle stick to the neutral position → System detects the neutral throttle signal, makes a long “beep-” sound → System detects battery voltage and makes several short “beep-” sounds, which denotes the number of battery cells →when self-test is finished →“♪ 1 2 3” tone should be emitted → Ready for start.
PAGE 3
Manual of QUIK Series Sensorless Brushless Motor Speed Controller 1.Enter program mode 4.Exit program 1 Turn off the ESC, Switch on transmitter, keep throttle stick to the neutral There are two ways to exit program mode: 、 position 、Press and hold the “SET” KEY, Switch on the ESC 3、Wait for 3 seconds, special tone like “♪ i3i3” should be emitted ,which 1 2 means program mode is entered 、 In step 2, after 3 long tone (The item #11)，please release the KEY within 2 seconds.
PAGE 4
Manual of QUIK Series Sensorless Brushless Motor Speed Controller Note: 1. 1 long “beeb-----” = 5 short “beeb-”. For example, in “Li-xx Cells Number” setting, 1 long “beeb-----” plus 1 short “beeb-” ( 5+1=6 ), means a 6 cells Li-xx battery pack.. 2.The boldface in above form is the default value. 3. Low voltage Protection threshold (Cutoff voltage) = Li-xx Cells Number * Cutoff threshold. Cutoff threshold is Protection threshold for one cell Li-xx.