User Manual

ManualsBrandsHobbyKing ManualsHobbyHobbyKing® ™ Brushless Car ESC 45A w/ Reverse

Manual of Quik Series Sensorless Brushless Motor Speed Controller

User Manual of Quik Series ESC for Car

V2.0

Features

 Full protection feature including low voltage, over-heat, throttle signal lost, startup protection and self-check.

 Compatible with sensorless brushless motor.

 Excellent startup performance, great throttle linear and quick throttle response.

 Support highest motor speed 240,000RPM(2 poles), 80,000RPM(6 poles) and 40,000(12 poles).

 The parameters of ESC can be configured via program card or key .

 System can automatically detect throttle neutral point and neutral range is adjustable.

 Three work mode can match different requirement.

 4 steps of maximum reverse force adjustment, 5 steps of maximum start force adjustment.

 3 steps of maximum brake force adjustment, 5 steps of drag brake force adjustment, 4 steps of initial brake force adjustment.

 Support 1 cell operation (min voltage: 3V, only available for XC-6A and XC-10A).

Specification

Battery Cell

P/N

Continuous

current

Li-XX Ni-H

Dimension (mm)

L×W×H

Weight

BEC

Program

card

Program

key

XC-6A 6A 1-2 3-8 12 x 20 x 5 4 1A/5V Yes NO

XC-10A 10A 1-2 3-8 22 x 17 x 7 8 1A/5V Yes NO

Quik-30A

30A 2-3 4-9 45x32x20 50 2A/5V Yes Yes

Quik -45A

45A 2-3 4-12 45x32x20 50 2A/5V Yes Yes

Quik -60A

60A 2-4 4-15 47x41x29 80 2A/5V Yes Yes

Quik -80A

80A 2-4 4-15 47x41x29 80 2A/5V Yes Yes

Quik -100A

100A 2-4 4-15 47x41x29 80 2A/5V Yes Yes

XC-150A 150A 2-6 5-18 96x55x21 180 0.2A/5V Yes NO

XC-120A-HV

120A 2-10 5-30 96x55x21 180 0.2A/5V Yes NO

Note: For XC-150A and XC-120A-HV, an UBEC or individual battery pack should be required to power the receiver and servos,

and the red line (+5V) in 3 pin must be pulled out !

Using ESC

Normal Startup Procedure

Move throttle stick to the neutral position Switch on the transmitter Connect battery pack to ESC System detects the

neutral throttle signal, makes a long “beep-” sound System detects battery voltage and makes several short “beep-” sounds, which

denotes the number of battery cells when self-test is finished ♪ 1 2 3 tone should be emitted ready for start.

Setting Throttle Range (Throttle range should be setup when a new transmitter is being used)

Switch off the ESC Switch on the transmitter Press and hold the “ SET ” KEY Switch on the ESC Push the

throttle stick to the top point of forward within two seconds wait for one second System detects the Max throttle signal, and

makes two “beep-” sounds, which denotes that Max throttle has been confirmed and saved Pull the throttle stick to the top point of

backward System detects the Min throttle signal, makes two “beep-” sounds, which denotes that Min throttle has been confirmed and

saved Release the “ SET ” KEY Setting is finished.

Push the throttle stick to the neutral position System detects the neutral throttle signal, makes a long “beep-” sound

System detects battery voltage and makes several short “beep-” sounds, which denotes the number of battery cells when self-test is

finished

♪ 1 2 3 tone should be emitted Ready for start.

If the system doesn’t detect the throttle signal, it will make “beep-” sounds continuously without stopping.

Summary of content (5 pages)

PAGE 1
Manual of Quik Series Sensorless Brushless Motor Speed Controller User Manual of Quik Series ESC for Car V2.0 Features Full protection feature including low voltage, over-heat, throttle signal lost, startup protection and self-check. Compatible with sensorless brushless motor. Excellent startup performance, great throttle linear and quick throttle response. Support highest motor speed 240,000RPM(2 poles), 80,000RPM(6 poles) and 40,000(12 poles).
PAGE 2
Manual of Quik Series Sensorless Brushless Motor Speed Controller Any fault in self- test, or voltage is over , it will make 20 very short “beep-” sounds. LED will light according to ‘beep-’ tone. The LED Status 1, The green LED lights when the car go forward, the red LED lights when the car is backward, both the red and green LED light when the car is braking 2, when the car stops, red LED and green LED don’t light.
PAGE 3
Manual of Quik Series Sensorless Brushless Motor Speed Controller 1.Enter program mode 4.Exit program 1 Turn off the ESC, Switch on transmitter, keep throttle stick to the neutral There are two ways to exit program mode: 、 position 、Press and hold the “SET” KEY, Switch on the ESC 3、Wait for 3 seconds, special tone like “♪ i3i3” should be emitted ,which 1 2 means program mode is entered 、 In step 2, after 3 long tone (The item #11)，please release the KEY within 2 seconds.
PAGE 4
Manual of Quik Series Sensorless Brushless Motor Speed Controller Note: 1. 1 long “beeb-----” = 5 short “beeb-”. For example, in “Li-xx Cells Number” setting, 1 long “beeb-----” plus 1 short “beeb-” ( 5+1=6 ), means a 6 cells Li-xx battery pack.. 2.The boldface in above form is the default value. 3. Low voltage Protection threshold (Cutoff voltage) = Li-xx Cells Number * Cutoff threshold. Cutoff threshold is Protection threshold for one cell Li-xx.
PAGE 5
Manual of Quik Series Sensorless Brushless Motor Speed Controller Adopting 2x16 point LCD panel, program card can make all setting conveniently and directly. The keys function KEY WR To FUNCTION To move the cursor vertically To confirm selected item To write and save setting cursor move the and change item or item or item value. parameter to ESC horizontally value Program procedure 1. Unplug the battery of ESC and connect the PPM wire to program card properly. 2.