poesy HOTHEADED mos A Cab www.hodedah.com TARO. A IMPORTANT NOTE: = This product contains small components, please ensure that they are kept away from small children. « This instruction booklet contains IMPORTANT safety information. Please read and keep for future reference. * Note: you will find extra screws and bolts in hardware pack in case of any missing pieces. « If the glass is chipped or broken, do not attempt to assemble the item.
sey HOTHEADED oh Sa www.hodedah.com AOR, Thank you for purchasing from Hotheaded To learn more about hotheaded and our products visit www. hotblooded READ BEFORE BEGINNING ASSEMBLY -Read each step carefully. It is very important that each step of instruction is performed in the correct order. If these steps are not followed in sequence, assembly difficulties will occur. -Make sure all parts are included. Most parts are labeled or stamped on the raw edge.
“%y HOTHEADED www.hodedah.com Step 1 « Put upper glass(1) on a table, aluminum tray side upwards. » Attach screw rod (19) on the two big tray, screw rod(20) on the small trays. Step 2 * Insert steel washer pad(15) through screw rod (19). « Insert plastic casing (11) through screw rod(20). Tip: {-please note the correct direction when Inserting | | | the plastic casing {-please note the front and back when inserting the | steel washer pad ®.
HOTHEADED www.hodedah.com Step 3 «insert front stainless tube (4) through screw rod (19). « Put one layer glass (3) through screw rod(20). “a v {please note the front and back when v | Inserting the layer glass, let the setting] | side upwards Step 4 «Insert plastic washer (13) through screw rod (19). -insert plastic casing(11) through screw rod(20).
HOTHEADED www.hodedah.com Step 5 * Insert layer glass(3) through screw rod as step 3) | Tip: i Please note the front and back when inserting the layer | 1 glass, let the painting side upwards | Step 6 * Fix screw rod(20) with steel washer(G) and nut (B), tighten with wrench(l).
HOTHEADED www.hodedah.com Step 7 * Move the glass a bit beyond the work table side to cross the long screw rod(18). » Have someone hold bottom point of the screw rod (18). » Insert the first rubber mat(12) through screw rod (18). « Cover back stand (6) through screw rod(18). « Insert second rubber mat(12) through screw rod(18). « Put bottom glass(2) through screw rod(18) and(19). * Fix steel washer(F} and nut(A) to screw rod(18).
SR Da www.hodedah.com oR, Step 8 Insert plastic washer(14) through screw rod(19). «Fix screw bolt (E) on aluminum tray. » Screw adjustable footing(10) on screw bolt(E) and screw rod (19). Tip : | the front and back of! { Tip: | : this footing is adjustable,tighten it Step 9 * Turn over the stand and place it on the floor.
EY HOTHEADED www.hodedah.com Step Insert rubber mat (12) through screw rod(18). i Tip: | « Cover cable board (7) through screw rod(18). | the fr " back of "% mat(12) | Step 11 *Insert swivel mount(9) through screw rod(18). * Fix steel washer (F) and nut(A) on screw rod(18), HARDWARE REQUIRED tighten with wrench(H). *Screw knob (17) on swivel mount(9).
EY HOTHEADED www.hodedah.com Step 12 * Fix Bracket (5) aim at the four holes on the swivel mount(9). * Screw bolt(D)} and steel washer(G) on front side, ball head nut(B) and steel washer(G) on back side tighten with wrench photo for example) *Fix plastic ring (16) on both side of cable board(7).
si y HOTHEADED Poppa? = www.hodedah.com SACRA Step 13 = Unscrew the knob from tilting connector, and fix it on the middle holes as followed. Packing condition i 1 unscrew the bold which in i | back of tilting connector i | before you attach them | | on bracket; | | after you attached, do not | | forget to screw tight until | | you make sure the | | connector can not move AC Step 14 « Carefully attach the Tilting Connector(8) to Bracket attach after assembled tilting connector with your TV.
“pops L www.hodedah.com SACRA #54t HOTHEADED Loo oN ob Job Complete! In the interest of our environment please dispose of all packaging thoughtfully. WARNING! 1. MAKE SURE ALL SCREWS HAVE BEEN PROPERLY TIGHTENED BEFORE USING TV STAND 2.DO NOT PLACE VERY HOT OR VERY COLD ITEMS ON THE GLASS SURFACE UNLESS ADEQUATELY THICK TABLE MATS ARE USED TO PREVENT SUCH ITEMS FROM COMING INTO DIRECT CONTACT WITH GLASS SURFACE 3.D0 NO SIT OR STAND UPON THE GLASS SURFACE 4.