NCA 450U Kit-RM High Performance Front & Rear Speaker Kit with 200 Watt Amplifier ForFor UseUse On 1998-2013 On rushmore Ultra Classics platform Andmodels Tri‐Glides installation Manual
Thank you for choosing the Hogtunes REV 450U KIT-RM speaker and amplifier kit for “Rushmore” platform Ultra Classics. Since positive word of mouth is the best way to grow our business, we want your new system to work as well as it was designed to. If you have any questions or concerns, we are here to help. The installation will be done in 3 major steps.
62F-RM Front Speaker Installation Instructions Step #1: Remove the seat and both wires (+ and -) from the battery. Remove the outer fairing/headlamp assembly and set aside. Refer to a service manual if you need help with this. NOTE: Placing a towel on the front fender can help prevent scratches or “dings” from dropped tools or fasteners, etc.
Step #3: I nstalling the new speaker: With the cabinet removed from bike, undo the four screws that hold the factory speaker to the cabinet. Carefully take off each speaker wire by disconnecting one at a time. Take a Hogtunes speaker and re-attach the factory speaker wires noting they will only go on one way.
362R-RM rear Speaker Installation Instructions Step #1: Remove the factory speaker grills by undoing the four screws on the front of the grills. Carefully lift up on each speaker and take the two wires off by pulling one at a time from the stock speaker. Remove the speakers. Step #2: Hogtunes 362R-RM rear speakers are a direct replacement for the OE speakers. The female OE “in-line” connectors mate with the male connectors on each speaker and only go on one way.
NCA 450-RM amplifier Installation Instructions Step #1: Over top of the radio, pull up to release each wire harness from the black plate via the factory “Christmas Tree” fasteners. If your bike has factory GPS, the small square antenna will need to be relocated just behind the voltmeter as shown in Fig 1.1 below. Remove the four factory T-20 “Torx” screws that go through the top of the black plate and into the top of the radio. Step #2: Figure 1.
Step #4: Figure 1.2 shown here. Figure 1.2 - Amplifier and mounting plate correctly oriented. The plate with four small holes is for mounting a popular Harley accessory. The white circles show tabs which are there for the “Christmas Tree” fasteners to re-secure the harnesses lifted earlier. Step #5: Also in Fig 1.2 is a white square which shows a smaller black 2 pin factory plug. The orange wire from the amp has a plug that goes directly into this factory harness.
routing the power and rear speaker harness Step #1: The power/ground harness and rear harness will pass together under the inner fairing where the main wire harness passes through on the brake side of the bike. Loosen the tank’s “chrome console” and run wires up and over the gas tank, but under the tank’s chrome console. There is a provision on the front of the tank console for wires to pass.
Step #3: Next to the “fader/no fader” switch is a 3 position switch to adjust the rear channel volume. On Ultra Classics, we use the bike’s built in fader control to allow you to adjust the front/rear volume from the radio itself. For best performance, this switch needs to be left in the +3 position. Step #4: Attach the amp’s red wire to the positive (+) battery terminal and the amp’s black wire to the negative (-) battery terminal. The factory battery wires are also re-installed at this point.
Adjusting Your System-Please Read! In order to make your new system perform as good as it was designed, please take a minute to understand and follow these tips: 1) S et your “Automatic Volume Control” (AVC) to 3 bars. After extensive on-road testing, we found that this AVC position works and sounds best. Your new amplifier has been specifically set-up for this radio setting. 2) Y our Hogtunes system is designed specifically for a motorcycle at speed.
Warranty Information Please Record Your Amplifier’s Serial # Here_________________________ Hogtunes speakers are warranted for a period of 20 years. The NCA 450-RM Amplifier is warranted for 3 years from original purchase date. Proof of purchase is required for all warranty claims. The warranty applies to the original retail customer and is not transferable. Please contact Hogtunes for all warranty claims.
Any audio system can be a distraction to the rider and/or passenger. Please use caution when playing your stereo, especially in traffic. www.hogtunes.
