Installation Guide

Installation Instructions
Models: SESD180, DESD180 with Notched Panel
1/4" Semi-Frameless Door and 3/8" In-Line Panel
#28
Wet Glazing
parts detail
#2 / #1
Cross-section
#5 / #1
Cross-section
w/ setting block
Outside
Outside
#29
Dry Glaze
Glazing Bead
Silicone
Bead
Fill void with silicone.
Push towards walls
after curb is set in place.
#1
#23
STEP 1 - Curb Installation (#1)
* Measure the wall to face of buttress wall where you want
the center of the unit to be installed.
* Subtract 1/16" from this. Mark location for reference.
* Cut the Stall Curb #1 to this length.
* Insert foam plug into each end of the Stall Curb.
and recess 1/8"
* Fill 1/8” void with silicone.
* Set the curb in place centered over where you marked.
* Secure with blue tape.
* Weep holes are to inside of shower.
* Do not screw the curb to threshold.
Mark Centerline
location for reference
Measure
#21
#21
#22
#4
#1
#6
#7
(outside
of unit)
Drawing not
proportioned
Pieces are cut
to size based off
your order
STEP 2 - Wall Channel (#4)
* Insert Vert. Wall Channel into curb, on face of buttress.
* Plumb channel with a level.
* Mark the hole locations onto the wall.
* Remove the channel and drill marked locations with
3/16" drill bit.
* Insert 2 - Wall Anchors #22 (may have to razor heads off
anchors flush to wall).
* Re-insert channel and secure with 2 - #21 screws.
* Follow with the Horizontal Channel and tape in place.
* Set Wall Channel #4 on top of the horizontal channel,
plumb with a level. Mark the hole locations onto the wall.
* Drill with a 3/16 bit. Secure with 2 - #21 screws and 3 -
#22 Wall Anchors.
#4
#1
#6
#27
#27
#7
#5
STEP 3 - Panel Sill (#5) and 3/8” Fixed Panel (#18)
* Measure the lower width of 3/8” Fixed Panel and subtract 3/8”.
* Cut the Panel Sill #5, to this length.
* Set the Panel Sill #5 into the Stall Curb #1 and butt to the Wall
Channel #7.
* Insert two Setting Blocks #27 into both horizontal Panel Sills.
Wet Glaze Option Only - If using silicone to bond the glass to
the wall channel and sill:
- Install 2 - #28 Centering Clips evenly spaced
into Panel Sill, offset from Setting Blocks.
- Insert 3 - #28 Centering Clips into the Wall channel.
Dry Glaze Option - If using push-in glazing vinyl to set the 3/8”
glass panel, do not use Centering Clips #28.
* Set 3/8” Glass Panel into Panel Sill and Wall Channel.
* Flush glass edge to exposed end of Panel Sill #5.
* Adjust top of glass flush to top of Wall Channel, place additional
setting blocks under glass if needed.
* Ensure vertical edge of 3/8” Glass Panel is plumb.
Wet Glaze Option - Temporarily, but securely fix Glass Panel
into position with blue painter’s tape.
Dry Glaze Option - Holding the glass panel in position, roll or
press the Glazing Bead into both sides of sill and wall channel
using a roller or smooth block of wood.
Check to ensure panel didn’t move.
Measure
STEP 4 - Curb Filler (#2)
* Measure from the edge of the 3/8” Glass Panel sill #5
to the Door side wall.
* Cut the Curb Filler #2 to this length.
* With the two forks pointing down and the vertical leg to
the front of the unit, snap the Curb Filler into the Stall
Curb.
* The slope of the Curb filler should be to the inside of the
shower.
Page 10
*** If using the Dry Seal, once the push in vinyl has been installed, it
cannot be easily removed without being replaced.