Installation Guide

ManualsBrandsHolcam ManualsShower DoorsDistinctive Elite 46-1/16- 47 in x 71-3/8 in Semi-Frameless Swing Door with In-Line Panel Oil Rubbed Bronze

Table Of Contents

Installation Instructions

Models: SESD180, DESD180

1/4" Semi-Frameless Door and 3/8" In-Line Panel

General Required Tools

* Pencil or water soluble felt pen

* Hacksaw with 24 tooth blade

* Metal file (smooth sharp edges)

* Tape measure

* Drill, electric or battery

* #2 Phillips Screw driver

* 7/64” and 3/16” drill bits

* Caulking gun

* Clear 100% Silicone

(recommended)

* 4 ft. Level

* Rubber mallet

* Razor knife

* Blue painters tape

SESD180

DESD180

Standard Door/Panel

Pages 3 - 5

SESD180

DESD180

with buttress

Pages 6 - 8

SESD180

DESD180

with notched panel

Pages 9 - 11

Pick a unit below that best represents your configuration.

IMPORTANT: Warnings and General Shower Door Information

Page 2

Thank you for purchasing this outstanding product!

This booklet will help you install your units safely and successfully.

SAFETY

WARNINGS:

GLASS FRAGILESHARPCAUTIONHEAVY

Scan this Barcode for Parts Bag BP.3143.NLT

P/N MM.5023

rev061818

Summary of content (12 pages)

PAGE 1
Installation Instructions Models: SESD180, DESD180 1/4" Semi-Frameless Door and 3/8" In-Line Panel P/N MM.5023 rev061818 Scan this Barcode for Parts Bag BP.3143.NLT Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully. IMPORTANT: Warnings and General Shower Door Information Page 2 SAFETY WARNINGS: HEAVY CAUTION SHARP GLASS FRAGILE Pick a unit below that best represents your configuration.
PAGE 2
SAFETY WARNINGS: HEAVY CAUTION SHARP GLASS FRAGILE CAUTION - READ THOROUGHLY BEFORE INSTALLATION Follow instructions: Instructions must be read and followed carefully to reduce the risk of serious injury during and after installation. Any deviation from these instructions can create safety hazards. Tempered Glass: Agalite enclosures glass panels are safety tempered to conform to general building codes. The intent of tempering is to reduce the risk of injury. Be careful handling tempered glass.
PAGE 3
Installation Instructions Models: SESD180, DESD180 1/4" Semi-Frameless Door and 3/8" In-Line Panel 4 Figure 1 - Exploded View 6 9 10 11 12 13 14 Not Shown 20 19 16 3 22 20 19 15 7 24 23 18 8 7 25 5 21 17 2 1 21 Parts List 1. EX.1022 - Stall Curb - 1 21. SP.2204 - Foam Plug - 2 9. Door Assembly-EX.1165-Hinge Jamb-1 2. EX.1025 - Curb Filer - 1 22. SP.2110 - #8 X 1/2 PHPH TEK - 3 10. VN.4034 - Hinge Sleeve - 1 3. EX.1268 - Hinge Wall Channel - 1 23. - 24. Magnetic Edge Cap Assembly -1 11. EX.
PAGE 4
Installation Instructions Models: SESD180, DESD180 1/4" Semi-Frameless Door and 3/8" In-Line Panel STEP 1 - Curb Installation (#1) * Measure the wall to wall where you want the center of the unit to be installed, subtract 1/16" from this. * Mark location for reference. * Cut the Stall Curb #1 to this length. * Insert foam plug #21 into each end of the Stall Curb and recess 1/8". * Fill 1/8” void with silicone. * Set the curb in place centered over where you measured, secure with blue tape.
PAGE 5
STEP 7 - Door Assembly / Pre-Hanging Prep * Attach Pull - Handle #18 to Door. * Dry run the position of Magnetic Catch Assembly, #23, #24 and mark location with marker on glass. * Apply small bead of silicone inside Catch Assembly and work onto edge of glass at mark. Let silicone dry. STEP 8 - Hang Door Assembly * Slide door assembly over the Wall Channel (Step 6). * Adjust door until top edge of the door is level and flush with top of 3/8” Glass Panel.
PAGE 6
Installation Instructions Models: SESD180, DESD180 with Buttress 1/4" Semi-Frameless Door and 3/8" In-Line Panel 4 Figure 1 - Exploded View 7 12 11 13 14 15 16 21 Not Shown 22 18 3 24 22 21 17 25 20 5 10 6 19 23 2 1 23 Parts List 1. EX.1022 - Stall Curb - 1 2. EX.1025 - Curb Filler - 1 3. EX.1268 - Hinge Wall Channel - 1 4. EX.1018 - Panel Wall Channel - 1 5. EX.1018 - Panel Sill Horizontal - 1 6. EX.1018 - Panel Sill Vertical - 1 7. - 9. VN.4075 - Clear PVC Latch Assy - 1 10. VN.
PAGE 7
Installation Instructions Models: SESD180, DESD180 with Buttress 1/4" Semi-Frameless Door and 3/8" In-Line Panel #23 Fill void with silicone. Push towards walls after curb is set in place. re Measu Silicone Bead Outside STEP 2 - Curb Filler (#2) * Measure from the face of the buttress wall to the Door side wall. * Cut the Curb Filler #2 to this length. * With the two forks pointing down and the vertical leg to the front of the unit, snap the Curb Filler into the Stall Curb.
PAGE 8
STEP 7 - Door Assembly / Pre-Hanging Prep * Attach Pull - Handle #20 to Door. * Dry run the position of Magnetic Catch Assembly, #25, #26 and mark location with marker on glass. * Apply small bead of silicone inside Catch Assembly and work onto edge of glass at mark. Let silicone dry. STEP 8 - Hang Door Assembly * Slide door assembly over the Wall Channel. (Step 6) * Adjust door until top edge of the door is level and flush with top of 3/8” Glass Panel.
PAGE 9
Installation Instructions Models: SESD180, DESD180 with Notched Panel 1/4" Semi-Frameless Door and 3/8" In-Line Panel 4 Figure 1 - Exploded View 8 12 11 13 21 14 15 16 22 Not Shown 18 3 24 22 21 17 25 10 20 #27 6 #21 #22 7 25 5 23 19 2 1 23 Parts List 1. EX.1022 - Stall Curb - 1 2. EX.1025 - Curb Filler - 1 3. EX.1268 - Hinge Wall Channel - 1 4. EX.1018 - Panel Wall Channel - 1 5. EX.1018 - Panel Sill - 1 6. EX.1018 - Panel Sill Horizontal - 1 7. EX.1018 - Panel Sill Vertical - 1 8. - 10.
PAGE 10
Installation Instructions Models: SESD180, DESD180 with Notched Panel 1/4" Semi-Frameless Door and 3/8" In-Line Panel STEP 1 - Curb Installation (#1) * Measure the wall to face of buttress wall where you want the center of the unit to be installed. * Subtract 1/16" from this. Mark location for reference. * Cut the Stall Curb #1 to this length. * Insert foam plug into each end of the Stall Curb. and recess 1/8" * Fill 1/8” void with silicone. * Set the curb in place centered over where you marked.
PAGE 11
STEP 7 - Door Assembly / Pre-Hanging Prep * Attach Pull - Handle #20 to Door. * Dry run the position of Magnetic Catch Assembly, #25, #26 and mark location with marker on glass. * Apply small bead of silicone inside Catch Assembly and work onto edge of glass at mark. Let silicone dry. STEP 8 - Hang Door Assembly * Slide door assembly over the Wall Channel. (Step 6) * Adjust door until top edge of the door is level and flush with top of 3/8” Glass Panel.
PAGE 12
Page intentionally left blank