Installation Guide

ManualsBrandsHolcam ManualsBathroomDistinctive 74-in H x 55-in to 58-in W Frameless Bypass/Sliding Matte Black Shower Door (Clear Glass)

Table Of Contents

General Required Tools

* Pencil or water soluble felt pen

* Hacksaw with 24 tooth blade

* Metal file (smooth sharp edges)

* Tape measure

* Drill, electric or battery

* #2 Phillips Screw driver

* 3/16” Carbide drill bit for tile

* 1/8" Drill bit for metal

* Caulking gun

* Clear 100% Silicone (recommended)

* 4 ft. Level

* Rubber mallet

* Razor knife

* Blue painters tape

* Booklet: MM.5037

SSE

DSE

Shower Slider

STE

DTE

Tub Slider

Pick a unit below that best represents your configuration.

IMPORTANT: Warnings and General Shower Door Information

Page 2

Thank you for purchasing this outstanding product!

This booklet will help you install your units safely and successfully.

SAFETY

WARNINGS:

GLASS FRAGILESHARPCAUTIONHEAVY

This installation sheet is a required component in Parts Bag BP.3541

Installation Instructions

Models: STE / SSE

DTE / DSE

1/4" Frameless Slider

- These instructions must be followed carefully to reduce the risk of serious injury. Any deviation from these

instructions can create a serious safety hazard.

- Glass panels are tempered to conform with general building and safety codes. Be very careful handling tempered

glass. Especially protect all edges of the glass from contact with hard surfaces.

- All exposed aluminum edges should be deburred to avoid serious injury.

Special Note: Drilling holes and anchoring horizontal sills and curbs into thresholds and tub decks is discouraged

because it can cause leaking and water damage below the unit. Use masking tape or double-sided tape to hold

components down during installation and then apply silicone for structural support and water protection. Exceptions

to this policy are necessary when components are structurally required to be anchored.

P/N MM.5037

rev061818

Summary of content (4 pages)

PAGE 1
Installation Instructions Models: STE / SSE DTE / DSE P/N MM.5037 rev061818 1/4" Frameless Slider This installation sheet is a required component in Parts Bag BP.3541 Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully. IMPORTANT: Warnings and General Shower Door Information Page 2 SAFETY WARNINGS: HEAVY CAUTION SHARP GLASS FRAGILE - These instructions must be followed carefully to reduce the risk of serious injury.
PAGE 2
Installation Instructions Page 2 Models: STE / SSE or DTE / DSE 1/4" Frameless Slider 12 ILLUSTRATION #1 1 3 Showerhead Wall 8 12 8 3 7 5 5 7 13 11 10 10 11 12 6 7 4 2 7 Parts List Item 1 2 3 4 5 6 Part # 1049 1062 1051 4032 7102 2206 QTY Description 1 Tub Header 1 Stay Clean Sill 2 Tub Jamb 1 TF-2B T-Fin 2 Sliding Glass Panel AVG-3 Center Guide 1 Item 7 8 9 10 11 12 2209 2256 QTY Description 4 Bumper Guides 4 Hanger Bracket Assy 2101 2217 2102 #8 x 1-1/2 FHPHSMS Wall Anchor #6 x
PAGE 3
Installation Instructions Page 3 Models: STE / SSE or DTE / DSE 1/4" Frameless Slider STEP 3 - TUB JAMBS: The Tub Jamb (3) opposite the shower head wall is installed first Set Tub Jamb in gap between the Stay Clean Sill (2) and wall Plumb the jamb Mark only the bottom Tub Jamb hole using the. factory hole as a template Ÿ Drill the hole with a 3/16” drill bit (carbide bit for masonry) Ÿ Insert one Wall Anchors (11) into the tile.
PAGE 4
Installation Instructions Page 4 Models: STE / SSE or DTE / DSE 1/4" Frameless Slider 7 ILLUSTRATION #7 Cushioned Knob 5 7 Inside Shower 5 Cushioned Knob Blind Fastener 3 Towel Bar 2 Cushioned Knob Outside Shower 3 Top view shows towel bar and knob locations for a shower head on right wall. If the shower head is on the left the panels would be reversed.