Installation Guide

ManualsBrandsHolcam ManualsAlcove Shower DoorsEclipse 60 in. W x 76 in. H Frameless Sliding Shower Door in Brushed Nickel

Table Of Contents

General Required Tools

* Pencil or water soluble felt pen

* Hacksaw with 24 tooth blade

* Metal file (smooth sharp edges)

* Tape measure

* Drill, electric or battery

* #2 Phillips Screw driver

* 3/16" drill bit carbide for tile

* 5/16” drill bit carbide for tile

* Caulking gun

* Clear 100% Silicone

(recommended)

* 4 ft. Level

* Rubber mallet

* Razor knife

* Blue painters tape

ECSE180

Shower Slider & 180° Panel

ECTE180

Tub Slider & 180° Panel

Pick a unit below that best represents your configuration.

IMPORTANT: Warnings and General Shower Door Information

Page 2

Thank you for purchasing this outstanding product!

This booklet will help you install your units safely and successfully.

SAFETY

WARNINGS:

GLASS FRAGILESHARPCAUTIONHEAVY

Scan this Barcode for Parts Bag BP.5004.NTL

Installation Instructions

Models: ECTE180 / ECSE180

3/8" Frameless Slider & 180° Panel

MM.5004_Rev. 05.8.2018

P/N MM.5004

rev061818

Summary of content (8 pages)

PAGE 1
Installation Instructions Models: ECTE180 / ECSE180 3/8" Frameless Slider & 180° Panel P/N MM.5004 rev061818 Scan this Barcode for Parts Bag BP.5004.NTL Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully. IMPORTANT: Warnings and General Shower Door Information Page 2 SAFETY WARNINGS: HEAVY CAUTION SHARP GLASS FRAGILE Pick a unit below that best represents your configuration.
PAGE 2
Page 2 SAFETY WARNINGS: HEAVY CAUTION SHARP GLASS FRAGILE CAUTION - READ THOROUGHLY BEFORE INSTALLATION Follow instructions: Instructions must be read and followed carefully to reduce the risk of serious injury during and after installation. Any deviation from these instructions can create safety hazards. Tempered Glass: Agalite enclosures glass panels are safety tempered to conform to general building codes. The intent of tempering is to reduce the risk of injury. Be careful handling tempered glass.
PAGE 3
Installation Instructions Page 3 Models: ECTE180 / ECSE180 3/8" Frameless Slider & 180° Panel 4 Figure 1 - Exploded View 3 11 7a 3 6 4 6 13 7a 1 2 15 14 16 10 8b 7b 8b 8c OR For Dry Seal 9 5 For Wet Seal HA.3001 - Roller Wheels ------------- 2 HA.3002 - Anti Jump Knobs --------- 2 HA.3003 - Bumper Stops ------------- 2 HA.3004 - Wall Collars / Pucks ----- 2 HA.3005 - Center Guide -------------- 1 HA.3007 - Panel Connectors ------- 2 BP.
PAGE 4
Page 4 Installation Instructions Models: ECTE180 / ECSE180 3/8" Frameless Slider & 180° Panel STEP 1 - Calculation: * Measure height of sliding glass panels (14): ___________ * Subtract 3 1/16" from this measurement: ___________ * New measurement is the height from the threshold to the center of the first Wall Puck Step 3. Slider panel height - 3 1/16 = ______ STEP 2 - Evaluate Threshold: * Maximum recommended vertical threshold outage from side to side is 1/4".
PAGE 5
Installation Instructions Page 5 Models: ECTE180 / ECSE180 3/8" Frameless Slider & 180° Panel STEP 6 - Install Panel Connectors on Header Tube: * Orient Header Tube (11) so that the two holes are facing up. * Insert a screwdriver into the center hole of the tube. * Slide a Plug into tube stopping it with the screwdriver. * Manipulate the plug so that the hole in the plug lines up with the hole in the tube. * Put the screw through connector plate and into plug. * Snug screws with the supplied Allen wrench.
PAGE 6
Page 6 Installation Instructions Models: ECTE180 / ECSE180 3/8" Frameless Slider & 180° Panel STEP 9 - Mount Header Tube: * Slide the Header Tube into wall collar with stoppers pointed up. Slide wall collar to right and tighten set screws * Slide the loose Wall Collar off the Header Tube and onto the opposite Wall Puck taking care the tube does not fall. * Center the Header tube within both Wall Collars and align the Panel Fixers so they are facing to the outside.
PAGE 7
Page 7 Installation Instructions Models: ECTE180 / ECSE180 3/8" Frameless Slider & 180° Panel STEP 11 - Mounting the Fixed Glass Panel: * Set the Fixed Panel into the Panel Sill: - Spaced panel 1/8" off of the wall. - NOTE: 1/8” gap will be filled with silicone during final steps of installation. - The Fixed Panel will protrude out of the end of the channel. * Holes in the glass should line up with the two Panel Connectors on the Header Tube.
PAGE 8
Page 8 Installation Instructions Models: ECTE180 / ECSE180 3/8" Frameless Slider & 180° Panel STEP 14 - Hanging and Adjusting the Sliding Panel: * From inside of the shower, carefully lift Sliding Panel (14) onto the Header Tube (11) and into the Center Guide (5). * Move each Bumper Stop (3) towards the walls. * Shower Head Wall: bring the Sliding Panel to the closed position, leaving an even 1/4”gap at the shower head wall.