User Manual

ManualsBrandsHOLLYLAND ManualsIntercom SystemHOLLYLAND HollyView SOLIDCOM M1 Wireless Intercom System

Table Of Contents

HOLLYLAND HollyView SOLIDCOM M1 User Manual

Manuals+

User Manuals Simplified.

HOLLYLAND HollyView SOLIDCOM M1 User Manual

November 17, 2021November 18, 2021

Home » HOLLYLAND » HOLLYLAND HollyView SOLIDCOM M1 User Manual

SOLIDCOM M1

User Manual

V1.0.0

FOREWORD

Thank you for purchasing Hollyland Full-Duplex wireless intercom system. Please read this instruction carefully before using the product. Wish you have a pleasant experience.

Contents [ hide

1 KEY FEATURES

2 PACKING LIST

3 PRODUCT INTERFACES

4 DISPLAY INTRODUCTION

5 GUIDE

6 PRODUCT INSTALLATION

7 PARAMETERS

8 SUPPORT

9 Documents / Resources

9.1 Related Manuals /

Resources

KEY FEATURES

Carrier-Grade Voice Quality, up to 450 Meters Line-of-Sight Usage Distance

1.9GHz Frequency, Support Frequency Configuration in Different Regions

Automatically Switching between External Omnidirectional Fiberglass Antenna and In-Built Panel Antenna

Full-Duplex Wireless Communicating

The Station Supports up to 8 Beltpacks to Talk at the Same Time. Station, App and Webserver Configuration Upgrade supported

Beltpack Supports Simultaneous Calls in 3 Groups

The Station Supports Cascading or Connecting with the 2/4 Wire Audio Systems

Station’s Power could be Supplied by POE Cascading or NP-F Type Batteries

In-Built Lithium Battery for the Beltpacks, Usage for over 6 hours

Portable Storage Charging Base, Easy to Carry

10 Levels Volume. Different Needs of Scenes Satisfied

PACKING LIST

Summary of content (8 pages)

PAGE 1
Manuals+ User Manuals Simplified. HOLLYLAND HollyView SOLIDCOM M1 User Manual November 17, 2021November 18, 2021 Home » HOLLYLAND » HOLLYLAND HollyView SOLIDCOM M1 User Manual SOLIDCOM M1 User Manual V1.0.0 FOREWORD Thank you for purchasing Hollyland Full-Duplex wireless intercom system. Please read this instruction carefully before using the product. Wish you have a pleasant experience.
PAGE 2
1. Station x1 2. Beltpack x8 3. Charging Base x1 4. LEMO Single-Ear Headset x2 5. High Gain Omnidirectional Antenna x8 6. POE Adapter x1 7. RJ45 to XLR Transferring Cable (5 meters) x1 8. 4Pin XLR Adapter x1 9. USB-Type-A to Type-C Transferring Cable x1 10. Battery for Beltpacks x16 11. 3/8 Installing Accessory x1 12. User Guide x1 * The exact quantity may vary on products configuration. Please take the actual quantity as standard. PRODUCT INTERFACES ① 3.
PAGE 3
A ASTATION ①Antenna Interface ②Up Key ③Left Key ④Menu/Confirm Key (Long Press to the Menu/ Short Press to Select) ⑤Right Key ⑥Down Key ⑦Power Button ⑧3/8 Screw Hole ⑨Interface for NP-F Type Battery ⑩Power Supply Interface ฀4-Wire Audio Input-Output Interface (RJ45 Interface) ฀USB Interface ฀3/8 Screw Hole ฀2-Wire Audio Input-Output Interface ฀POE Interface B belt pack ①Antenna ⑦Right Key/C Group Key (The beltpack is not grouped when the ②Mute/Talk Switch Key, Press Down for Talk, Up for Mute indicator li
PAGE 4
A STATION MAIN DISPLAY INTRODUCTION ① Current Battery Voltage of Station ② Current Status of Beltpack TALK: The beltpack is able to talk while listening. MUTE: The beltpack is able to listen but unable to talk. LOST: The beltpack is disconnected from the station. LINK: The beltpack is linking to the station.
PAGE 5
2. Select “Master and Slave” to Set the Station as Master Device/Slave Device. 2.1 If there’s only one kit of devices, the station needs to be set as Master Device; When two or more kits are cascaded, the station can be set as Master Device/ Slave Device. 2.2 When the station is set as Master Device, The beltpack number will automatically switch to 1-8; When the station is set as Slave Device, The beltpack number will automatically switch to 9-16. 2.
PAGE 6
1. Station Installation 1. Install the antenna according to the picture. 2. Connect the power adapter, or install NP-F type battery. 3. Press the power button to power it on. 2. Beltpack Installation 1. Open the battery compartment, insert the battery in the direction marked on the battery. 2. Switch the power switcher on to power on. 3. After the beltpack status changes from “LOST” to “TALK”, You can Talk Now. Press the top button will change to “MUTE”. The beltpack is able to listen but unable to talk.
PAGE 7
Interfaces Station Beltpack POE Interface (RJ45) Power Supply Interface (RJ45) 4 Wire Audio Interface USB Interface 2 Wire Audio Interface USB Type-C Interface 3.
PAGE 8
Mailer User Manual - Download [optimized] Mailer User Manual - Download Manuals+, home privacy