Owner manual

ManualsBrandsHollywood Racks ManualsFor bicyclesHR1000 SportRider 2 bike

Sport Rider

Instruction Manual

Model HR1000 – 2 Bike Hitch Rack

with ratcheting hooks OR Precision Slide Clamps



Not to be used on any trailer, fifth

wheel or vehicle being towed by

another vehicle

 Weight Limit 45lbs/20 kg per bike

 2 bike maximum capacity

 Optional locking kits available

ID# Description Qty

A MAIN RACK ASSY 1

B1 Ratchet style short frame hook OR

B2 Precision slide short frame hook 1

C1 Ratchet style long frame hook OR

C2 Precision slide long frame hook 1

D RECEIVER TUBE & SPACER 1

E LEFT SIDE WHEEL TRAY 2

F RIGHT SIDE WHEEL TRAY 2

G REC. TUBE STOP BOLTS 2

H LOWER BRACKET 1

I 8MM BOLTS 4

J FLAT WASHERS 4

K 5MM HEX KEY 1

L LOCK WASHERS 2

M ½-13 THREADED HITCH PIN 1

N HITCH PIN CLIP 1

P WHEEL TUBE STOP SCREWS 2

HOLLYWOOD RACKS

Pour instructions en Français, continuer aux pages 8 et 9.

Summary of content (9 pages)

PAGE 1
HOLLYWOOD RACKS Pour instructions en Français, continuer aux pages 8 et 9.
PAGE 2
Fig. 1 Assembly & Installation Procedure: Fig. 2 Step 1: Locate holes on main rack assembly, bracket and hardware (Fig. 1) Step 2: Loosely assemble bracket to main rack as shown in Fig. 2 & 3. Bolts (I) inserts through lock washer (L), then flat washer (J), then top plate and into bottom plate Do Not tighten! Step 3: Slide main rack assembly onto Receiver tube as shown in Fig. 4 & 5. Adjust position so that is 3 or 4 inches between the end of the rack and end of the receiver tube.
PAGE 3
Step 7A: Install frame hooks: For ratchet style hooks only: Slide long frame hook down vertical post facing vehicle. Then slide short frame hook onto post, facing away from vehicle. You should hear be able to hear the spring loaded lever engaging the teeth on the post as shown in fig. 8. Step 6: Installing into a 1 ¼” trailer Note: The receiver tube comes ready for installation into a 2” hitch. If you have a 1 ¼” hitch, use the provided hex wrench to remove the plastic spacer as shown in Fig. 9.
PAGE 4
Step 6 B: Installing into a 2” trailer hitch Important! When inserting the hitch pin bolt, the bolt should pass through the receiver tube first then through the plastic spacer. Place lock washer and flat washer onto hitch pin bolt as indicated. Insert the receiver tube into the hitch. Align the holes, insert the hitch pin bolt and tighten securely using a ¾” wrench. Fig. 12 Fig. 13 Fig. 14 Install Hitch pin clip after tightening bolt Folding Down Vertical Post Fig.
PAGE 5
Folding Up the Wheel Holders To fold up the wheel holders, rotate and remove the front retaining pins. Then rotate the tube up and re-install the pins. See Fig. 17a &17b 17a 17b Installing Bikes on the Rack Pre-position the wheel trays to fit the bike’s wheel base (center to center distance between the wheel axels) such that they are directly beneath each wheel. To adjust the wheel trays, loosen the knobs and slide along the wheel holder support tube. Tighten knobs securely.
PAGE 6
Tips for carrying woman’s bikes and bikes with slanted top tubes Adjust the wheel trays so that the hook will rest in the bike frame’s top tube and seat tube, as shown in Fig. 19a and 19b. 18e 18d To release the frame hook, depress the Lever and pull the hook up. Tip: you may have to push the hook down a bit while holding in the lever to release it.
PAGE 7
Limited Lifetime Warranty (effective January 1, 2008): Hollywood Racks will warrant its car racks and accessories during the time that an original retail purchaser owns the product subject to the exclusions and limitations of this warranty. Hollywood Racks will remedy defects in materials and workmanship by repairing or replacing (at its option) a defective part or the complete rack without charge for labor or parts.
PAGE 8
Hollywood Sport Rider. Modele HR1000 Porte-vélo pour atelage remorque pour 2 vélos. Ne pas utiliser ce produit sur une remorque ou un véhicule qui est remorqué.
PAGE 9
Inclinaison du mât central. For un accès facile a la porte arrière, le mât central s’incline en tournant et en enlevant la broche comme sur Fig 16a-16d. Assurez vous de reserrer la vis après avoir redresser le mât. Rangement des support de roues Pour ranger les supports de roues, tounez et enlevez les broches de devant. Fig 17a & 17b.