Instruction Manual

ManualsBrandsHOLOPHANE ManualsFloodlight MarineHOLOPHANE IM-60-C Predator Small Floodlight Marine

Installation and

Maintenance

Manual

1. INTRODUCTION

1.1 Product Description. The Predator floodlights have been

designed and tested in accordance with UL844 and UL595. These

floodlights comply with applicable paragraphs of Sections 501, 502,

and 503 of the National Electrical Code.

-The fixture identification label provides information regarding

suitable environmental applications.

-The floodlight model size is referred to in Figure 1.

-Major components of the floodlight are identified in Figure 1.

-The Predator floodlights have been designed to allow permanent

installation of the yoke or box mount and housing while still

providing easy maintenance and repair.

-The lamp, all electrical components, and the reflector can be

accessed by opening the door.

-Using a socket wrench, the door can be opened by loosening

captive door screws.

AFTER INSTALLATION DELIVER THIS

MANUAL TO OWNER

GR421

IM-60-C

Predator

Small Floodlight Marine

-All electrical components and the lens are contained on the door

and the door can be removed easily and without tools (once the

captive door screws are loosened).

-Doors can be replaced as units and repaired in a shop under

protected conditions.

-The reflector located within the housing can be replaced as

needed. Different types of reflectors will provide different light

distributions.

1.2 Alternate Information Sources. If additional

questions arise relative to the Predator floodlight that this document

or your supplier cannot answer please refer them to:

Holophane

Field Service Department

P.O. Box 3004

Newark, OH 43058-3004

866-759-1577

2. INSTALLATION

2.1 Tools and Materials Required. The following tools

and materials are required during installation of the Predator

floodlight.

TABLE 1. Installation Tools and Materials

DESCRIPTION USE

3/8" hex head socket wrench Captive door screws

3/4" hex head wrench Yoke bolt

1/2" hex head socket wrench Box Mount

Pliers Cord grip (if applicable)

Torque wrench Captive door screws and bolts

(inch and foot lbs.)

Wire nuts

2.2 Yoke Mount Installation.

WARNING

DO NOT USE A PHOTOCONTROL IN A LOCATION

HAVING A UL CLASSIFICATION OF CLASS I, DIV. 2

OR CLASS II, DIV. 1. DO NOT USE FUSING IN A

LOCATION HAVING A UL CLASSIFICATION OF

CLASS I. FAILURE TO FOLLOW THESE WARNING

INSTRUCTIONS MAY RESULT IN FIRE AND

SIGNIFICANT PROPERTY DAMAGE.

2.2.1 Bolt the yoke to the mounting structure through the provided

holes in the yoke using two 3/8" bolts (not provided).

2.2.2 Loosen the captive door screws attaching the door to the

housing. Open the door.

2.2.3 Detach the power disconnect plug from the disconnect

receptacle in the housing.

2.2.4 If needed, remove the door by removing the cotter pin from

the hinge pin and sliding the door hinge pins out of the housing.

2.2.5 Use UL approved watertight power cord fittings (not

provided) on all installations. If installed in a Marine location, use

rigid metal conduit or AVC Marine cable (not provided) and water-

tight cable grip fittings (not provided) for power supply conductors.

WARNING-READ THESE INSTRUCTIONS

CAREFULLY BEFORE ATTEMPTING TO INSTALL OR

MAINTAIN THIS FIXTURE. WORK MUST BE DONE

BY QUALIFIED PERSONNEL.

WARNING-BE CERTAIN THAT ALL ELECTRICAL

POWER IS DISCONNECTED FROM THE FIXTURE

BEFORE INSTALLING OR MAINTAINING THE FIXTURE.

WARNING-FOLLOW LAMP MANUFACTURER'S

OPERATING AND MAINTENANCE INSTRUCTIONS.

IMPORTANT SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE WARNINGS MAY

RESULT IN DEATH, INJURY OR SIGNIFICANT

PROPERTY DAMAGE.

DISCONTINUED

Summary of content (4 pages)

PAGE 1
Predator ® Small Floodlight Marine IMPORTANT SAFETY INSTRUCTIONS WARNING-READ -All electrical components and the lens are contained on the door and the door can be removed easily and without tools (once the captive door screws are loosened). -Doors can be replaced as units and repaired in a shop under protected conditions. -The reflector located within the housing can be replaced as needed. Different types of reflectors will provide different light distributions. 1.2 Alternate Information Sources.
PAGE 2
TI NU ED Figure 1 W H D 13-1/8" 17-7/8" 7-7/8" GR420 NOTE POWER CORD FITTING The threaded hole in the back of the housing is tapped for 1/2-14 NPT. 2.2.6 25 lbs. GR418 2.3.5 Use UL approved watertight cord grip fittings (not provided) on all installations. If installed in a Marine location, use rigid metal conduit or AVC Marine cable (not provided) and watertight cable grip fittings (not provided) for power supply conductors to thruway box mount. 2.3.
PAGE 3
. MAINTENANCE 3.1 Relamping and cleaning. 3.1.1 3.1.2 3.2 Door Replacement/Repair. 3.2.1 3.2.2 De-energize the floodlight. Wipe off the exterior of floodlight to remove dirt or debris that could enter when the door is opened. 3.2.3 Loosen the captive door screws attaching the door to the housing. Open the door. 3.2.4 Detach the power disconnect. 3.2.5 Remove the cotter pin from the hinge pin. 3.2.6 Slide the door hinge pins from the housing. 3.3 Electrical Component Replacement.
PAGE 4
.2 Wire Guard Installation and Maintenance. When The following options or accessories may be present on your installation. installed, the wire guard helps protect the tempered glass lens from damage. 4.1 Visor Installation and Maintenance. 4.2.1 4.2.2 When installed, the visor limits the vertical spread of emitted light. 4.1.1 Attach the clips to the shield, one in the center and one on each corner at approximately the location of the holes. The shield goes into the narrow side of the clip.