HOLUX FunTrek130 Pro/ FunTrek130 FunTrek130 Pro/ FunTrek130 User Manual Holux Technology Inc.
HOLUX FunTrek130 Pro/ FunTrek130 Copyright Declaration HOLUX is trademarks of HOLUX Technology, Inc. All other trademarks belong to registered companies. The contents of this manual will be modified without further notice. Without the written consent of HOLUX Technology, Inc, this manual may not be translated or copied. Copyright HOLUX Technology, Inc. All rights reserved. Software Copyright FunTrek130 software is China and international copyright law protection. Copyright HOLUX Technology, Inc.
HOLUX FunTrek130 Pro/ FunTrek130 Product Caution About operation environment The operating temperature for the product is between -10℃~60℃. Operating or recharging in an environment with a temperature over 45℃ might cause the system malfunction. However, this should be considered a normal phenomenon. Please do not operate under extreme temperatures. About the altimeter The device estimates altitude based on air pressure.
HOLUX FunTrek130 Pro/ FunTrek130 enough to supply the device. About the battery 1. Use only the original factory approved power adapter. 2. A Lithium battery is built into the device. To prevent fire or skin burns, do not disassemble, pierce, impact, or expose the battery to fire. The battery will crack, explode, or release dangerous chemicals if placed in a fire. Important instructions 1. Note: Replacing with an incorrect battery may result in an explosion.
HOLUX FunTrek130 Pro/ FunTrek130 off the power and remove the battery. These proposals are only applicable to FunTrek130 Pro/ FunTrek130, its battery, charger or any other accessories.
HOLUX FunTrek130 Pro/ FunTrek130 Product introduction Receiver function: GPS Positioning: :Hidden antenna design, high-sensitivity GPS receiver chip can do quick positioning. Electronic compass: : Provides direction for location information, with compass function. Altimeter: :Measure the altimeter by using the GPS altitude and pressure altimeter calibration. Touch screen LCD: A high resolution color, touch screen TFT LCD with backlight.
HOLUX FunTrek130 Pro/ FunTrek130 Application functions: : G-Finder: :Use the G-Finder feature to calibrate points in order to measure the field area. Coordinate Datum switching: :Support Beijing1954, Xian 80, Taiwan TWD 67, TWD 97 and WGS 1984 coordinates system which are switchable. You also can set more than 250 coordinates. Area calculation: :Measures area for Resources Field Survey. Average location: :Calculate average value of coordinates and average altitude.
HOLUX FunTrek130 Pro/ FunTrek130 Table of Contents Copyright Declaration .......................................................................................................... ii Software Copyright .............................................................................................................. ii Product Caution .................................................................................................................. iii Product introduction........................................
HOLUX FunTrek130 Pro/ FunTrek130 Reposition...................................................................................................................27 Average position.........................................................................................................28 Copy to new................................................................................................................29 Project to new......................................................................................
HOLUX FunTrek130 Pro/ FunTrek130 Product Spec Main program spec Item Spec parameter Operation interface Simplified Chinese/ Traditional Chinese/ English/ Czech switching operation Support external program Yes The numbers of waypoints 2000 The numbers of routes 1000 Waypoints of every route 1000 Track log 10000 The total number of sub-record 1000 Record by time interval Yes Record by distance interval Yes Atomically record Yes Continuous recording time 8 hours Datum Yes Beijing 195
HOLUX FunTrek130 Pro/ FunTrek130 Hardware spec CPU Battery Samsung S3C2416 ARM9 BASE, 8.5 hrs (on the basis of 50% backlight 400MHz brightness) Rechargeable, Li-Ion 1050mAh GPS chip High Sensitivity (-159dBm) GPS Chip. Waterproof IPX-6 Memory 128M Memory IO interface Built-in 2GB Flash.. USB 2.0 (mini USB ) Support SD V2.0 Adaptor Input: 100 ~ 240V, 0.15 A, 50~60Hz Display 3.
HOLUX FunTrek130 Pro/ FunTrek130 Unit Overview Component Function Description: (Front View) Item Description Touch Screen LCD The device is using the touch-screen control. Right button When the device is powered off, press the right button for 3 seconds to turn on this device. When powered on, press this button for 3 seconds to turn off. Left button When the device is powered on, press the left button to switch to the Main Menu, Trip Computer page and Navigation. LED 1.
HOLUX FunTrek130 Pro/ FunTrek130 Basic Operation Power on and off When device is turned on, press and hold the right button for 3 seconds to power off the device. The prompt "Saving data… please wait." will appear while the device is powering off. When device is turned off, press and hold the right button for 3 seconds to power on. Note: Please do not power off the devices when you use the “Training” or “Area calculation” functions, the track log can’t be saved normally.
HOLUX FunTrek130 Pro/ FunTrek130 Power on and Positioning First positioning Please take the device out of the room, and turn on the device. Then enter into the satellite status page to displays the position status. When searching satellite signal will display “Acquiring”. “2D Fixed” means the positioning status mode. “3D fixed” means the coordinate information is available for reference. Only after the positioning is successfully for the first time, it will begin to record the track.
HOLUX FunTrek130 Pro/ FunTrek130 Right button Backlight Step: Press the right button once to enter the operation page as shown above. Click the button to increase/decrease the backlight brightness. Auto Light FunTrek130 is equipped with a sensor that automatically detects the ambient light level and adjusts the backlight brightness to save power. Step: Press the right button once to enter the operation page.
HOLUX FunTrek130 Pro/ FunTrek130 calibration when they first powered on. The device will record track log automatically. Manually record: press the button to enter the new a track log. On the page, users can edit name, notes, and view sport modes. Press the Press the recording. Press the button to save the track log, and start to record. button to pause recording; press the button to start/continue button to stop recording, and save the track data.
HOLUX FunTrek130 Pro/ FunTrek130 Note: Checkpoint name can be input up to 20 words, notes can be input up to 50 words. New waypoint Step: Press the right button once to enter the operation page. The bottom of page is the area to mark waypoints . Press the button to enter the waypoint edit page. You can edit waypoint name, select waypoint symbol, add notes, edit waypoint coordinates location and input waypoint altitude. button to set Click “location” button to define the waypoint coordinates.
HOLUX FunTrek130 Pro/ FunTrek130 Left button Trip Computer Step: Press the left button once to enter the Trip Computer. In the Trip Computer page, you can view travel distance, travel time, current speed and altitude, and the other 40 Trip Computer. Use the button to check more navigation data. Change Trip Computer Items Step: Press the setting button . You can select the item that you want to change.
HOLUX FunTrek130 Pro/ FunTrek130 Page Display Selection In the Trip Computer, press the button. You can use the change the number of pages displayed on the screen. and buttons to : displays 3 items of Trip Computer on screen. : displays 8 items of Trip Computer on screen. View statistical curve FunTrek130 Pro/ FunTrek130 can record the height, speed, pressure, time and distance curve for the user to view the analysis. Step: Press the left button once to enter the Trip Computer.
HOLUX FunTrek130 Pro/ FunTrek130 Note: If you didn’t record track log, the device doesn’t have the altitude, speed, and pressure information and it also doesn’t display the statistical curve. Compass Step: Press the left button once to enter the Trip Computer. Press the button to enter compass page. On the compass page, you can view current direction, azimuth and compass. Compass which has not done with its calibration can not accurately show the direction. Press the the Compass.
HOLUX FunTrek130 Pro/ FunTrek130 If the screen is unlocked, press the left button for 3 seconds to lock the screen, the message of "Screen locked” appears on the screen. The “unlock" message pops up on the screen if press the left button for 3 seconds. Once the screen is locked, press the left button for 3 seconds to unlock the screen. Connect to PC When the FunTrek130 Pro/ FunTrek130 is connected to a PC, the following prompt will appear. You can choose to enter storage mode or charging mode.
HOLUX FunTrek130 Pro/ FunTrek130 Charging mode Connect FunTrek130 Pro/ FunTrek130 to the PC with an USB cable. When the prompt appears, click to enter charging mode. When the device is power off and connect to the PC, enter charging mode. Screenshot FunTrek130 Pro/ FunTrek130 can take a screenshot and save as a picture. Press both the left and right buttons at once to take a screenshot. If screenshot is successful, a prompt will appear.
HOLUX FunTrek130 Pro/ FunTrek130 Main menu list When the device turned is on, the status bar is displayed on the top of main menu. The six icons are function lists in below of main menu. Status Main Menu Status bar Satellite information Icon / Description Operation The signal strength / Click the icon to enter the satellite page GPS positioning Time Icon Description Operation Time information Click the icon to enter Alarm is turned on Click the icon to enter. Please refer to Alarm.
HOLUX FunTrek130 Pro/ FunTrek130 Storage mode Icon Description Operation Track and waypoint data stored in microSD card. Please refer to Storage media Track and waypoint data store in internal memory. Please refer to Storage media Heart rate monitor (HRM) (FunTrek130 Pro only) Icon Description Operation HRM sensor is turned on. Please refer to Heart Rate Monitor HRM sensor is turned off.
HOLUX FunTrek130 Pro/ FunTrek130 Backlight Icon Description Operation Backlight is on. Please refer to Backlight Backlight is off. Please refer to Backlight Locked the screen Icon Descript Operation The screen is locked. Please refer to Screen Lock/ Unlock The screen is unlocked. Please refer to Screen Lock/ Unlock Track log Icon Descript Operation The track log was recording. Please refer to New Track The track log was paused.
HOLUX FunTrek130 Pro/ FunTrek130 Follow Course With Follow Course function, it can guide you to your pre-defined destination. The available options are “By track”, “By route” and “G-Finder”. By Track When selecting the saved track, you can set several locations as ”Starting”, “Ending” or “Check point” waypoints. And the waypoint location can be switched. Step: On the main menu, click “Follow Course” to enter the waypoint menu. Click “By track” icon to enter the track waypoint menu.
HOLUX FunTrek130 Pro/ FunTrek130 By Route When selecting the saved track, you can set two waypoints as “Start point” or “End point”. The selected track can be set as the destination of designated waypoints, and these two waypoints location can be switched. Step: On the main menu, click “Follow Course” to enter the waypoint menu. Click “By route” icon to enter the track waypoint menu. On the track list, select the desired track record.
HOLUX FunTrek130 Pro/ FunTrek130 G-Finder The G-Finder enables users to mark their starting points. It helps you get the current position and distance from where you started. This helps guide you to return to the starting point. Step: On the main menu page, click “Follow Course”. Click “G-Finder”. Press the “Current position”: Current location will be set as the G-Finder point. “User define”: Input coordinates value of the G-Finder point.
HOLUX FunTrek130 Pro/ FunTrek130 View Map With the map view, user can browse the tracks, waypoints, routes and areas. Following are the map features: Press the button to zoom in/out on the map. Adding marker on the map: Press the button to mark the location on the map. button again to locate the position in the middle of the screen which Press the makes it easier to browse. Press the If you have created your own map on the device, press map name, then you can enter the map screen.
HOLUX FunTrek130 Pro/ FunTrek130 Managing the Tracks With Track management, you view, edit, or copy the track, or get the detail information of each track log. You can also search for a particular track. Notes: The recording log will automatically stop when the recording time or distance reaches its maximum limit. Search track log Step: On the main menu page, click “Tracks” to enter the track list. Press the After completed, press “confirmation” button to display the search result.
HOLUX FunTrek130 Pro/ FunTrek130 includes the amount of carbon reduction, the tree planting quantity. The car mode does not include the same functions as walking mode. Note: If you edit sport mode, press the button to refresh the track information. Altitude/ Speed Plot With Altitude map, you can playback the track record to view the changes of the altitude. Step: On the main menu page, click “Tracks” to enter the track list.
HOLUX FunTrek130 Pro/ FunTrek130 On the main menu page, click “Tracks” to enter the track list. Select the track that you will operate, click to enter the Track Menu. Select “view map”, the screen will display the track. You can zoom in or zoom out to change the scale. The track name is shown on the top of the screen. Press the button to set the map display direction. Press the button and click the location on the map to mark a point.
HOLUX FunTrek130 Pro/ FunTrek130 Copy to new Step: On the main menu page, click “Tracks” to enter the track list. Select the track that you will operate, click to enter the Track Menu. Select “Copy Track” to enter the edit track page. Press the confirmation button to copy. View multiple Tracks Step: On the main menu page, click “Tracks” to enter the track list. Check the tracks you want to display. You can select up to three tracks to be displayed at one time.
HOLUX FunTrek130 Pro/ FunTrek130 Waypoints Search waypoints There are plenty of destinations that you can choose. Use the search function to quickly find the desired destination. Step: On the main menu page, click “Waypoints”. Click the waypoints. Press the confirmation button to display the searching results. button to enter the input method page. Enter the key words of the Note: After search, if you exit the waypoints management page, it will no longer display the search results.
HOLUX FunTrek130 Pro/ FunTrek130 View map Step: On the main menu page, click “Waypoints”. Select the point that you will operate, click to enter the Waypoints menu. Select "Browse”, the screen will display the waypoint position. Press the button and click the location on the map to mark a point. Press the button to move the point to the center of the screen.
HOLUX FunTrek130 Pro/ FunTrek130 Edit waypoints Step: On the main menu page, click “Waypoints”. Select the point that you will operate, click to enter the Waypoints menu. Select “Edit” to enter the waypoint edit page. You can edit waypoint name, select waypoint symbol, add notes, edit waypoint coordinates location, and input waypoint altitude. On “Coordinates input” page, press the format and system. button to set the condinates Press the confirmation button to delete.
HOLUX FunTrek130 Pro/ FunTrek130 Step: On the main menu page, click “Waypoints”. Select the point that you will operate, click to enter the Waypoints menu. Select “reposition” to update the waypoints coordinates to the current location coordinates. When repositioning is completed, a message appears on the screen. Press the "confirm" button. If GPS does not acquire the satellite signal, the device can not repositioning.
HOLUX FunTrek130 Pro/ FunTrek130 On the edit page, press Press the button to save the waypoint information. button to calibrate altimeter by average altitude. On the Location map of 10 meters, 20 meters or 30 meters radius, when the sampling point is focused on the center, the average coordinate value is closely paralleled the true value. On the Altitude map, the height value is the horizontal axis, and the origin of the horizontal axis is the average height.
HOLUX FunTrek130 Pro/ FunTrek130 On the main menu page, click “Waypoints”. Select the point that you will operate, click to enter the Waypoints menu. Select “Project to new” and enter the distance and bearing. Press the save. Enter a new waypoint edit page, a confirmed coordinates and altitude information. Press the button to create a project waypoint.
HOLUX FunTrek130 Pro/ FunTrek130 Application Application contains all main functions of FunTrek130 Pro/ FunTrek130. Shortcut All functions in application page can be set as shortcuts on the main page. Step: On the main menu page, click “Application”. Press the Select the function that you will set as shortcut, and click to enter shortcut list. Select the location of the shortcut, and return to the application page. button to enter function list.
HOLUX FunTrek130 Pro/ FunTrek130 In the “Storage Card\app” folder, place the SmartMaps icon which is in PNG format. For example, the filename is “smartmaps.png”. In the main menu, this icon represents the third party software’s icon. In the “Storage Card\app” folder, create an INF file for SmartMaps. For example, “smartmaps.0409.inf”. Refer to the following guideline: name=SmartMaps icon=\Storage Card\app\smartmaps.png exec=\Storage Card\app\SmartMaps\smartmapspna.
HOLUX FunTrek130 Pro/ FunTrek130 Inf file naming convention is the “Software name, Language ID number”. Language ID number have to cooperate with FunTrek130 Pro/ FunTrek130 languages. If FunTrek130 Pro/ FunTrek130 main program is the Simplified Chinese version, the inf file name should be "Software Name .0804." (in Simplified Chinese). If the third-party software operating language is English, and FunTrek130 Pro/ FunTrek130 main menu displays third-party software in Simplified Chinese names.
HOLUX FunTrek130 Pro/ FunTrek130 “Cadence Grade”: Before you set the Cadence grade, please read the message that appears on the screen. Press the the appropriate cadence range. button to enter cadence grade list and select Users can define the cadence range. Click “User Define” to enter the minimum cadence value and press the “confirmation” button. Next, enter the maximum cadence value and press the “confirmation” button to save.
HOLUX FunTrek130 Pro/ FunTrek130 The training information page is based on the connection situation, then display different status: The sensor is disconnected, it displays as “---”; The sensor is connected and the signal is good, it displays the data and the icon is blinking; The sensor is connected, but the signal is poor and the display data shown is below than the minimum value for 1 to 5 seconds, cadence and speed data decreases, the icon does not blinking; The heart rate data is display
HOLUX FunTrek130 Pro/ FunTrek130 “Last training”: You can review the detail information of last training. Press the button to refresh the information.
HOLUX FunTrek130 Pro/ FunTrek130 Area calculation Area calculation can immediately measure the area, and the routes can be saved as a track log. Available options are “By track”, “By vertices”, and “By fixed-width”. By track The track size is measured by the track length. To calculate the length, trace the route of the track log until the end and return back to the starting point. Step: On the main menu page, click “Applications” to enter the Program menu.
HOLUX FunTrek130 Pro/ FunTrek130 Click “Price of length” or “price of area” button and input price of length/area. You can view the total price of length/area on the track log display page. Press the log. button to save the track, and press the “OK” button to save the track Note: Please do not power off the device when you use the “Area Calculation” function, the track log can’t be saved normally. By Vertices Manually set vertices points to calculate the area enclosed by the vertices.
HOLUX FunTrek130 Pro/ FunTrek130 On the length/area unit page, press the button to change the unit of length/area. Click “Unit of length” or “Unit of area” button to enter the unit list. Users can click one of the unit buttons to “Move down”, “Insert before”, “Insert behind” and “Delete” the unit. On this page, press the button to add other units. Click “Price of length” or “price of area” button and input price of length/area.
HOLUX FunTrek130 Pro/ FunTrek130 Select “By fixed-width” icon. Click “Width” and “Unit” to input the width length and its measurement unit. Press button to enter track display page. Press button to enter again “Width” and “Unit”. When completed, press the Press On the length/area unit page, press the button to change the unit of length/area. Click “Unit of length” or “Unit of area” button to enter the unit list.
HOLUX FunTrek130 Pro/ FunTrek130 Geocaching Visit www.geocaching.com website to download the geocaching documents. Information The information includes “Difficulty”, “Terrain”, “Cache Size” and “Trackable” and Hints. Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Geocaching” icon. The cache that has been found will be marked as contrarily, it is marked as . Click Geocaching to view the information.
HOLUX FunTrek130 Pro/ FunTrek130 Mark Found Step: On the GeoRadar page, press the Press the button to mark found. button to mark not found. Add Geocaching Notes Step: On the Compass page, press the After adding the comments, it returns to the GeoRadar page. button to mark found and add notes.
HOLUX FunTrek130 Pro/ FunTrek130 Calendar Step: On the main menu page, click “Applications” icon to enter the Program menu. Click “Calendar” icon to view the calendar page. Use the button to change month. Alarm clock Step: On the main menu page, click “Applications” icon to enter the Program menu. Click “Alarm clock” icon to enter the Alarm clock page. Press the Press the Press the button to turn on the alarm clock. button to save the value. button to turn off the alarm clock.
HOLUX FunTrek130 Pro/ FunTrek130 Calculator Step: On the main menu page, click “Applications” icon to enter the Program menu. Click “Calculator” icon to enter the Calculator page. Note: Input with up to 13 digits can be entered into the calculator. If the result exceeds 13 places, it will be displayed using scientific notation. Stopwatch Step: On the main menu page, click “Applications” icon to enter the Program menu. Click “Stopwatch” icon to enter the Stopwatch page.
HOLUX FunTrek130 Pro/ FunTrek130 Unit Conversion Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Unit” icon. Users can converts units of length, area, weight and volume. Click the input box and enter the value that you want to convert. You can do two conversions at one time. Click unit name to convert units. Health Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Health” icon.
HOLUX FunTrek130 Pro/ FunTrek130 Tips Tips function can help user to understand FunTrek130 Pro/ FunTrek130 and GPS knowledge. The default is displayed at power on. Users can view all tips content in application function. Step: On the main menu page, click the “Applications” icon to enter the Applications menu. Press the “Tips” icon to view the contents. Routes You can use waypoints to build routes, and edit routes name, description, and points.
HOLUX FunTrek130 Pro/ FunTrek130 Step: On the main menu page, click “Routes”. Select the route that you will operate, click to enter the Routes Menu. Select “Details” to view the detail information of the selected route. After you have reached the destinations, user can view the route name, comments, starting destinations. The starting and ending points link to a closed areas perimeter and dimension, and the route creates the changes of date and time.
HOLUX FunTrek130 Pro/ FunTrek130 Edit Step: On the main menu page, click “Routes”. Select the route that you will operate, click to enter the Routes menu. Select “Edit” to enter the route edit page. You can edit route name, add notes, edit route points. Click “Points” to enter point list. Click the point that you will operate to enter the point operation menu. On this page, you can “forward”, “backward”, “insert” and “delete” the points.
HOLUX FunTrek130 Pro/ FunTrek130 Copy to new Step: On the main menu page, click “Routes”. Select the route that you will operate, click to enter the Routes menu. Select “Copy a new”, you can copy a new route name, description, and points. After editing, press the button to copy a new route. Reverse to new With “Reverse to new” function, you can create a route in the opposite direction with the original route. Step: On the main menu page, click “Routes”.
HOLUX FunTrek130 Pro/ FunTrek130 Settings Personal The Profile function contains “Odometer”, “Track Log”, “Age & Weight”, “Background” and “Customized Maps”. Odometer You can save trip information in ODO1 or ODO2. Step: On the main menu page, click Settings. Select “Personal” to enter you personal settings list. Select “Odometer” to enter “ODO1” or “ODO2”. The default value is “ODO1”. Note: “ODO1” and “ODO2” are the same functions that can save the trip information.
HOLUX FunTrek130 Pro/ FunTrek130 Track Record Manually/ Automatically record track User can set the track record mode, select start tracking manually or automatically, and track the interval recording time. Step: On the main menu page, click Settings. Select “Personal” to enter your personal settings list. Select “Track Log” to enter the track log mode. Select “Manually” or “Automatically”.
HOLUX FunTrek130 Pro/ FunTrek130 Select "Distance" or "Time" to enter the enable/disable menu. Select “Enable” to enter the time or distance interval. When completed, press the confirmation button. Age & Weight Step: On the main menu page, click Settings. Select “Personal” to enter your personal settings list. Select “Age & Weight” to enter the personal information list. Select each item in turn to enter appropriate information.
HOLUX FunTrek130 Pro/ FunTrek130 Create Map FunTrek130 Pro/ FunTrek130 supports the Convert Tool to transfer smd map file, which enables user to create a new smd map to be added in the device. Steps: Use Convert Tool to convert bmp, jpg, and other map images into smd map. Please refer to the Convert Tool’s user manual. In the Holux device or SD card, create a folder name “hmp”. Place the converted smd file into the “hmp” folder, and start the FunTrek130 Pro/ FunTrek130.
HOLUX FunTrek130 Pro/ FunTrek130 Sensors Sensors contain “ANT+ Heart Rate Monitor”, “ANT+ Bike Cadence Sensor”, “ANT+ Bike Speed Sensor”, “Compass”, “Altitude” and “Screen”. ANT+ Heart Rate Monitors (FunTrek130 Pro only) Search heart rate monitor sensor, the steps are: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Heart Rate Monitor”, and press the “Search” button.
HOLUX FunTrek130 Pro/ FunTrek130 The details page displays the sensor’s information, such as S/N number; manufacture ID, model number, hardware version, software version and R-R Interval. The model number of Heart Rate Monitor sensor is 10. ANT+ Bike Cadence Sensors (FunTrek130 Pro only) Step: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Cadence Sensor”, and press “Search” button.
HOLUX FunTrek130 Pro/ FunTrek130 ID, model number, hardware version and software version. The model number of Cadence sensor is 20. ANT+ Bike Speed Sensors (FunTrek130 Pro only) Step: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Speedometer”, and press “Search” button. After searching match speed sensor, the device will display the list. Select the speed sensor that you need, and press the confirmation button to enable the function.
HOLUX FunTrek130 Pro/ FunTrek130 Step: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Compass”. Press the button to calibrate the compass. Altimeter Users can use GPS to calibrate or manually calibrate the altimeter. Step: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Altimeter” to view the option of altimeter calibration mode. You can select “GPS” or “Manual” calibration.
HOLUX FunTrek130 Pro/ FunTrek130 Step: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Screen”, a confirmation message will appear on the screen. Press the confirmation button, and start to calibrate screen. After calibrating the screen, tap the screen or wait for 30 seconds to exit. System Left key- Info pages Use the “Left key- Info pages” to set the project displayed on Trip information and the auto-flip.
HOLUX FunTrek130 Pro/ FunTrek130 Step: On the main menu page, click Settings. Select “System”. Select” “Left key- Info pages”. Select” “Select pages”. You can select by checking items to be displayed for the Left Key operation. Available options are: Trip Computer1, Trip Computer2, Altitude Graph, Compass and Information. When completed, it returns to the main menu page.
HOLUX FunTrek130 Pro/ FunTrek130 Note: “Auto select”: If GPS is already in the positioning mode or the barometer has not been calibrated, the device will automatically use GPS to measure the altitude. If both cases happened at the same time, the default is barometer. Speed mode FunTrek130 Pro/ FunTrek130 provides speed display including speedometer and GPS. Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”.
HOLUX FunTrek130 Pro/ FunTrek130 Select “Volume” to set the volume setting. Note: For details on beep information, refer to the device pop-up message. Auto shutdown Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Auto Power Off” to set the auto power off setting. Note: If FunTrek130 fails to acquire a fix within the set time, it will automatically power off.
HOLUX FunTrek130 Pro/ FunTrek130 Select User Grid in Coordinates Format List, and enter the parameter page. Select the parameter you want to define, and the digital keyboard appears. In longitude and latitude page, you can use and to change the directions. Set the respective parameters. When completed, it returns to the previous screen. Coordinate Datum Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”.
HOLUX FunTrek130 Pro/ FunTrek130 On the “Datum” page, select “User Datum”. Set the respective parameters. When completed, it returns to the previous screen. Units Users can set the units of Speed/ Distance. Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Units” to enter the options list. Select “Metric” or “Imperial” units. When completed, it returns to the previous screen.
HOLUX FunTrek130 Pro/ FunTrek130 When completed, it returns to the previous screen. Storage media Users can save track log files into the internal memory or the micro SD card. Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Storage media”. Select “Holux Internal Memory” or “SD card”. When completed, a “Change will not take effect until the device restarts. Restart it right now?” message appears on the screen.
HOLUX FunTrek130 Pro/ FunTrek130 Clear counters Clear counters enable users to clear the existing trip information that contains with the Odometer, total CO2/Tree Saved, and total rising/drop height information. Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Clear counters”, and select the items that you want to reset.
HOLUX FunTrek130 Pro/ FunTrek130 Show tips at start Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Show tips at start”. Select “Open” to show tips when you restart the device. If you select “Close”, the tips will not appear when you restart the device. When you restart the device, you can also disable the tips pop-up by checking the “Do not display tips on next start up”.
HOLUX FunTrek130 Pro/ FunTrek130 altimeter. When current altitude reaches the set value, the altitude alert message will appear ob the screen. The alert can help climbers to prevent the acute mountain sickness (AMS). If the altimeter detected current altitude reaches or exceeds the set value within 1 minute, the altitude alert message will appear on the screen.
HOLUX FunTrek130 Pro/ FunTrek130 ezTour Plus Installation To download the recorded track log and view it on your computer, first, you will need to install the bundled ezTour Plus. Insert the bundled installation CD into the computer’s CD drive to install ezTour Plus. For details, please refer to the included ezTour Plus user manual.
HOLUX FunTrek130 Pro/ FunTrek130 Website: www.holux.