HOLUX FunTrek 132 FunTrek 132 User Manual Holux Technology Inc.
HOLUX FunTrek 132 Copyright Declaration HOLUX is trademarks of HOLUX Technology, Inc. All other trademarks belong to registered companies. The contents of this manual will be modified without further notice. Without the written consent of HOLUX Technology, Inc, this manual may not be translated or copied. Copyright HOLUX Technology, Inc. All rights reserved. Software Copyright FunTrek 132 software is China and international copyright law protection. Copyright HOLUX Technology, Inc.
HOLUX FunTrek 132 Product Caution About operation environment The operating temperature for the product is between -10℃~60℃. Operating or recharging in an environment with a temperature over 45℃ might cause the system malfunction. However, this should be considered a normal phenomenon. Please do not operate under extreme temperatures. About the altimeter The device estimates altitude based on air pressure. Its means that altitude readings for the same location may vary with air pressure changes.
HOLUX FunTrek 132 About the battery 1. Use only the original factory approved power adapter. 2. A Lithium battery is built into the device. To prevent fire or skin burns, do not disassemble, pierce, impact, or expose the battery to fire. The battery will crack, explode, or release dangerous chemicals if placed in a fire. Important instructions 1. Note: Replacing with an incorrect battery may result in an explosion. When disposing of the battery, follow the instructions.
HOLUX FunTrek 132 Product introduction Receiver function: GPS Positioning： ：Hidden antenna design, high-sensitivity GPS receiver chip can do quick positioning. Electronic compass： ：Provides direction for location information, with compass function. Altimeter： ：Measure the altimeter by using the GPS altitude and pressure altimeter calibration. Touch screen LCD: A high resolution color, touch screen TFT LCD with backlight.
HOLUX FunTrek 132 Application functions： ： G-Finder： ：Use the G-Finder feature to calibrate points in order to measure the field area. Coordinate Datum switching： ：Support Beijing1954, Xian 80, Taiwan TWD 67, TWD 97 and WGS 1984 coordinates system which are switchable. You also can set more than 250 coordinates. Area calculation： ：Measures area for Resources Field Survey. Average location： ：Calculate average value of coordinates and average altitude.
HOLUX FunTrek 132 Table of Contents Copyright Declaration............................................................................................................................................ii Software Copyright................................................................................................................................................ii Product Caution...................................................................................................................................
HOLUX FunTrek 132 Geocaching ................................................................................................................................................. 34 Calendar...................................................................................................................................................... 36 Alarm clock..................................................................................................................................................
HOLUX FunTrek 132 Product Spec Main program spec Item Spec parameter Operation interface Simplified Chinese/ Traditional Chinese/ English/ Czech switching operation Support external program Yes The numbers of waypoints 2000 The numbers of routes 1000 Waypoints of every route 1000 Track log 10000 The total number of sub-record 1000 Record by time interval Yes Record by distance interval Yes Atomically record Yes Continuous recording time 8 hours Datum Yes Beijing 1954 Yes Xian 80
HOLUX FunTrek 132 Hardware spec GPS chip Battery High Sensitivity (-165dBm) GPS Chip. Up to 15 hrs (Backlight off) Removable & Rechargeable, Li-Ion 1150mAh Memory 128M mobile DDR SDRAM Waterproof Internal 4GB Flash. IPX-6 Support microSD card up to 32GB IO interface USB 2.0 (mini USB ) Display 3.0 ‘’WQVGA (16:9) TFT LCD Adaptor Transflective Touch Screen (Sunlight viewable) Input: 100~240V, 0.
HOLUX FunTrek 132 Unit Overview Component Function Description: (Front View) Item Description Touch Screen LCD The device is using the touch-screen control. Right button When the device is powered off, press the right button for 3 seconds to turn on this device. When powered on, press this button for 3 seconds to turn off. Left button When the device is powered on, press the left button to switch to the Main Menu, Trip Computer page and Navigation. LED 1. The LED flashes red when charging 2.
HOLUX FunTrek 132 Basic Operation Power on and off When device is turned on, press and hold the right button for 3 seconds to power off the device. The prompt "Saving data… please wait." will appear while the device is powering off. When device is turned off, press and hold the right button for 3 seconds to power on. Note: Please do not power off the devices when you use the “Training” or “Area calculation” functions, the track log can’t be saved normally.
HOLUX FunTrek 132 Power on and Positioning First positioning Please take the device out of the room, and turn on the device. Then enter into the satellite status page to displays the position status. When searching satellite signal will display “Acquiring”. “2D Fixed” means the positioning status mode. “3D fixed” means the coordinate information is available for reference. Only after the positioning is successfully for the first time, it will begin to record the track.
HOLUX FunTrek 132 Right button Backlight Step: Press the right button once to enter the operation page as shown above. Click the button to increase/decrease the backlight brightness. Auto Light FunTrek 132 is equipped with a sensor that automatically detects the ambient light level and adjusts the backlight brightness to save power. Step: Press the right button once to enter the operation page.
HOLUX FunTrek 132 notes, and view sport modes. Press the button to save the track log, and start to record. Press the button to pause recording; press the Press the button to stop recording, and save the track data. button to start/continue recording. Note: Track log name can be input up to 20 words, notes can be input up to 50 words. When device is manually powered off, the track log will be automatically saved.
HOLUX FunTrek 132 New waypoint Step: Press the right button once to enter the operation page. The bottom of page is the area to mark waypoints . Press the button to enter the waypoint edit page. You can edit waypoint name, select waypoint symbol, add notes, edit waypoint coordinates location and input waypoint altitude. Click “location” button to define the waypoint coordinates. Press the button to save the coordinates edit result. and system.
HOLUX FunTrek 132 Left button Trip Computer Step: Press the left button once to enter the Trip Computer. In the Trip Computer page, you can view travel distance, travel time, current speed and altitude, and the other 40 Trip Computer. Use the button to check more navigation data. Change Trip Computer Items Step: Press the setting button . You can select the item that you want to change. Click the item to enter the Trip Computer list, and use the up/down button to flip page and search.
HOLUX FunTrek 132 Page Display Selection In the Trip Computer, press the displayed on the screen. button. You can use and buttons to change the number of pages : displays 3 items of Trip Computer on screen. : displays 8 items of Trip Computer on screen. View statistical curve FunTrek 132 can record the height, speed, pressure, time and distance curve for the user to view the analysis. Step: Press the left button once to enter the Trip Computer.
HOLUX FunTrek 132 Compass Step: Press the left button once to enter the Trip Computer. Press the button to enter compass page. On the compass page, you can view current direction, azimuth and compass. Compass which has not done with its calibration can not accurately show the direction. Press the button to calibrate the compass. For details, please refer to the Compass. General information Step: Press the left button once to enter the Trip Computer.
HOLUX FunTrek 132 Screenshot FunTrek 132 can take a screenshot and save as a picture. Press both the left and right buttons at once to take a screenshot. If screenshot is successful, a prompt will appear. When the FunTrek 132 is connected to a PC in storage mode, the saved screenshot can be accessed in the "sc" folder. Note: Do not use the capture screen function when the screen is locked.
HOLUX FunTrek 132 Main menu list When the device turned is on, the status bar is displayed on the top of main menu. The six icons are function lists in below of main menu. Status Main Menu Status bar Satellite information Icon / Description Operation The signal strength / GPS positioning Click the icon to enter the satellite page Time Icon Description Operation Time information Click the icon to enter Alarm is turned on Click the icon to enter. Please refer to Alarm. Alarm is turned off.
HOLUX FunTrek 132 Heart rate monitor (HRM) Icon Description Operation HRM sensor is turned on. Please refer to Heart Rate Monitor HRM sensor is turned off. Please refer to Heart Rate Monitor Cadence Icon Description Operation Cadence sensor is turned on. Please refer to Cadence Cadence sensor is turned off.
HOLUX FunTrek 132 Follow Course With Follow Course function, it can guide you to your pre-defined destination. The available options are “By track”, “By route” and “G-Finder”. By Track When selecting the saved track, you can set several locations as ”Starting”, “Ending” or “Check point” waypoints. And the waypoint location can be switched. Step: On the main menu, click “Follow Course” to enter the waypoint menu. Click “By track” icon to enter the track waypoint menu.
HOLUX FunTrek 132 By Route When selecting the saved track, you can set two waypoints as “Start point” or “End point”. The selected track can be set as the destination of designated waypoints, and these two waypoints location can be switched. Step: On the main menu, click “Follow Course” to enter the waypoint menu. Click “By route” icon to enter the track waypoint menu. On the track list, select the desired track record. Select “Route name”, and set “waypoint name” position as the waypoint.
HOLUX FunTrek 132 G-Finder The G-Finder enables users to mark their starting points. It helps you get the current position and distance from where you started. This helps guide you to return to the starting point. Step: On the main menu page, click “Follow Course”. Click “G-Finder”. Press the “Current position”: Current location will be set as the G-Finder point. “User define”: Input coordinates value of the G-Finder point. “Waypoint”: Select waypoint of the G-Finder point.
HOLUX FunTrek 132 View Map With the map view, user can browse the tracks, waypoints, routes and areas. Following are the map features: Press the button to zoom in/out on the map. Adding marker on the map: Press the button to mark the location on the map. Press the again to locate the position in the middle of the screen which makes it easier to browse. Press the If you have created your own map on the device, press can enter the map screen.
HOLUX FunTrek 132 Create Map FunTrek 132 supports the Convert Tool to transfer smf map file, which enables user to create a new smf map to be added in the device. Steps: Use Convert Tool to convert bmp, jpg, and other map images into smf map. Please refer to the Convert Tool’s user manual. In the Holux device or SD card, create a folder name “hmp”. Place the converted smf file into the “hmp” folder, and start the FunTrek 132.
HOLUX FunTrek 132 Tracks With Track management, you view, edit, or copy the track, or get the detail information of each track log. You can also search for a particular track. Notes: The recording log will automatically stop when the recording time or distance reaches its maximum limit. Search track log Step: On the main menu page, click “Tracks” to enter the track list. Press the After completed, press “confirmation” button to display the search result. button to enter the input page.
HOLUX FunTrek 132 Note: If you edit sport mode, press the button to refresh the track information. Altitude/ Speed Plot With Altitude map, you can playback the track record to view the changes of the altitude. Step: On the main menu page, click “Tracks” to enter the track list. Select the track that you will operate, click to enter the Track Menu. Click “Altitude/ Speed Plot” to enter the altitude page.
HOLUX FunTrek 132 Press the button and click the location on the map to mark a point. Press the button to move the point to center of the screen. Edit track Step: On the main menu page, click “Tracks” to enter the track list. Select the track that you will operate, click to enter the Track Menu. Select “Edit” to edit track name, notes and sport modes. If you change the sport mode, press the button to refresh the track information.
HOLUX FunTrek 132 Copy to new Step: On the main menu page, click “Tracks” to enter the track list. Select the track that you will operate, click to enter the Track Menu. Select “Copy Track” to enter the edit track page. Press the confirmation button to copy. View multiple Tracks Step: On the main menu page, click “Tracks” to enter the track list. Check the tracks you want to display. You can select up to three tracks to be displayed at one time.
HOLUX FunTrek 132 Mass Storage Read the microSD card data Connect FunTrek 132 to the PC with a USB cable and turn on the device. On the main menu, click “Mass Storage” icon to enter the storage mode. Folders In Storage mode you will be able to see the folders in the memory card. Folder Name Description bg Stores background pictures. The user can add or delete pictures in this folder. map Stores the navigation program. sc Store screenshot pictures. track Stores track files.
HOLUX FunTrek 132 Application Application contains all main functions of FunTrek 132. Shortcut All functions in application page can be set as shortcuts on the main page. Step: On the main menu page, click “Application”. Press the Select the function that you will set as shortcut, and click to enter shortcut list. Select the location of the shortcut, and return to the application page. button to enter function list.
HOLUX FunTrek 132 In the “Storage Card\app” folder, place the SmartMaps icon which is in PNG format. For example, the filename is “smartmaps.png”. In the main menu, this icon represents the third party software’s icon. In the “Storage Card\app” folder, create an INF file for SmartMaps. For example, “smartmaps.0409.inf”. Refer to the following guideline: name=SmartMaps icon=\Storage Card\app\smartmaps.png exec=\Storage Card\app\SmartMaps\smartmapspna.
HOLUX FunTrek 132 the inf file name should be "Software Name .0804." (in Simplified Chinese). If the third-party software operating language is English, and FunTrek 132 main menu displays third-party software in Simplified Chinese names. Then English is used for the third-party software operation. If the language ID number and FunTrek 132 language does not match, an error will occur when running the third-party software.
HOLUX FunTrek 132 ANT+ Heart Rate Monitor, ANT+ Bike Cadence Sensor and ANT+ Bike Speed Sensors sections. After connected, it starts to receive the data. Click “Training” button to enter the training page. “HR Grade”: Before you set the HR grade, please read the message that appears on the screen. Press the button to enter HR Grade list and select the appropriate heart rate range. “Cadence Grade”: Before you set the Cadence grade, please read the message that appears on the screen.
HOLUX FunTrek 132 The sensor is disconnected, it displays as “---”; The sensor is connected and the signal is good, it displays the data and the icon is blinking; The sensor is connected, but the signal is poor and the display data shown is below than the minimum value for 1 to 5 seconds, cadence and speed data decreases, the icon does not blinking; The heart rate data is displayed as the last time, the icon does not blinking; The sensor is connected, but the signal is poor or the display
HOLUX FunTrek 132 Area calculation Area calculation can immediately measure the area, and the routes can be saved as a track log. Available options are “By track”, “By vertices”, and “By fixed-width”. By track The track size is measured by the track length. To calculate the length, trace the route of the track log until the end and return back to the starting point. Step： On the main menu page, click “Applications” to enter the Program menu. Click “Area” icon to enter the area calculation page.
HOLUX FunTrek 132 Click “Price of length” or “price of area” button and input price of length/area. You can view the total price of length/area on the track log display page. Press the button to save the track, and press the “OK” button to save the track log. Note: Please do not power off the device when you use the “Area Calculation” function, the track log can’t be saved normally. By Vertices Manually set vertices points to calculate the area enclosed by the vertices.
HOLUX FunTrek 132 On the length/area unit page, press the button to change the unit of length/area. Click “Unit of length” or “Unit of area” button to enter the unit list. Users can click one of the unit buttons to “Move down”, “Insert before”, “Insert behind” and “Delete” the unit. On this page, press the button to add other units. Click “Price of length” or “price of area” button and input price of length/area. You can view the total price of length/area on the track log display page.
HOLUX FunTrek 132 Press button to enter track display page. Press button to enter again “Width” and “Unit”. When completed, press the Press On the length/area unit page, press the button to change the unit of length/area. Click “Unit of length” or “Unit of area” button to enter the unit list. Users can click one of the unit buttons to “Move down”, “Insert button to display the measure of the track area. button to complete and save the result.
HOLUX FunTrek 132 Geocaching Visit www.geocaching.com website to download the geocaching documents. Information The information includes “Difficulty”, “Terrain”, “Cache Size” and “Trackable” and Hints. Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Geocaching” icon. The cache that has been found will be marked as as . Click Geocaching to view the information.
HOLUX FunTrek 132 Press the button to mark not found. Add Geocaching Notes Step: On the Compass page, press the After adding the comments, it returns to the GeoRadar page. button to mark found and add notes.
HOLUX FunTrek 132 Calendar Step: On the main menu page, click “Applications” icon to enter the Program menu. Click “Calendar” icon to view the calendar page. Use the button to change month. Alarm clock Step: On the main menu page, click “Applications” icon to enter the Program menu. Click “Alarm clock” icon to enter the Alarm clock page. Press the Press the Press the button to turn on the alarm clock. button to save the value. button to turn off the alarm clock.
HOLUX FunTrek 132 Calculator Step: On the main menu page, click “Applications” icon to enter the Program menu. Click “Calculator” icon to enter the Calculator page. Note: Input with up to 13 digits can be entered into the calculator. If the result exceeds 13 places, it will be displayed using scientific notation. Stopwatch Step: On the main menu page, click “Applications” icon to enter the Program menu. Click “Stopwatch” icon to enter the Stopwatch page.
HOLUX FunTrek 132 Unit Conversion Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Unit” icon. Users can converts units of length, area, weight and volume. Click the input box and enter the value that you want to convert. You can do two conversions at one time. Click unit name to convert units. Health Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Health” icon.
HOLUX FunTrek 132 Waypoints Search waypoints There are plenty of destinations that you can choose. Use the search function to quickly find the desired destination. Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Waypoints” icon. Click the Press the confirmation button to display the searching results. button to enter the input method page. Enter the key words of the waypoints.
HOLUX FunTrek 132 View map Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Waypoints” icon. Select the point that you will operate, click to enter the Waypoints menu. Select "Browse”, the screen will display the waypoint position. Press the button and click the location on the map to mark a point. Press the button to move the point to the center of the screen.
HOLUX FunTrek 132 Edit waypoints Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Waypoints” icon. Select the point that you will operate, click to enter the Waypoints menu. Select “Edit” to enter the waypoint edit page. You can edit waypoint name, select waypoint symbol, add notes, edit waypoint coordinates location, and input waypoint altitude. On “Coordinates input” page, press the button to set the condinates format and system.
HOLUX FunTrek 132 Reposition With reposition, you can use the current point to replace the original coordinates with the updated waypoints coordinates. Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Waypoints” icon. Select the point that you will operate, click to enter the Waypoints menu. Select “reposition” to update the waypoints coordinates to the current location coordinates.
HOLUX FunTrek 132 waypoints’ coordinates value are replaced with the average coordinates value. On the edit page, press Press the button to save the waypoint information. button to calibrate altimeter by average altitude. On the Location map of 10 meters, 20 meters or 30 meters radius, when the sampling point is focused on the center, the average coordinate value is closely paralleled the true value.
HOLUX FunTrek 132 Select “Project to new” and enter the distance and bearing. Press the Enter a new waypoint edit page, a confirmed coordinates and altitude information. Press the create a project waypoint. 44 button to save.
HOLUX FunTrek 132 Routes You can use waypoints to build routes, and edit routes name, description, and points. New routes Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Routes” icon. Press the Click “points” to enter the point list. Click the selects single or multiple waypoints. After added waypoints, return to new routes page. Press the button to enter a new routes page. button to select waypoints add into the routes.
HOLUX FunTrek 132 Details The details information contains name, length and area. Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Routes” icon. Select the route that you will operate, click to enter the Routes Menu. Select “Details” to view the detail information of the selected route. After you have reached the destinations, user can view the route name, comments, starting destinations.
HOLUX FunTrek 132 Edit Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Routes” icon. Select the route that you will operate, click to enter the Routes menu. Select “Edit” to enter the route edit page. You can edit route name, add notes, edit route points. Click “Points” to enter point list. Click the point that you will operate to enter the point operation menu.
HOLUX FunTrek 132 Copy to new Step: On the main menu page, click the “Applications” icon to enter the Program menu. Click the “Routes” icon. Select the route that you will operate, click to enter the Routes menu. Select “Copy a new”, you can copy a new route name, description, and points. After editing, press the button to copy a new route. Reverse to new With “Reverse to new” function, you can create a route in the opposite direction with the original route.
HOLUX FunTrek 132 Settings Personal The Profile function contains “Odometer”, “Track Log”, “Age & Weight”, and “Background”. Odometer You can save trip information in ODO1 or ODO2. Step: On the main menu page, click Settings. Select “Personal” to enter you personal settings list. Select “Odometer” to enter “ODO1” or “ODO2”. The default value is “ODO1”. Note: “ODO1” and “ODO2” are the same functions that can save the trip information.
HOLUX FunTrek 132 Track Record Manually/ Automatically record track User can set the track record mode, select start tracking manually or automatically, and track the interval recording time. Step: On the main menu page, click Settings. Select “Personal” to enter your personal settings list. Select “Track Log” to enter the track log mode. Select “Manually” or “Automatically”. If "Manually" is selected you must use the right button to create a new track in order to begin recording.
HOLUX FunTrek 132 When completed, press the confirmation button. Age & Weight Step: On the main menu page, click Settings. Select “Personal” to enter your personal settings list. Select “Age & Weight” to enter the personal information list. Select each item in turn to enter appropriate information. When completed, press confirmation button to save your setting. Background Step: On the main menu page, click Settings. Select “Personal” to enter your personal settings list.
HOLUX FunTrek 132 Sensors Sensors contain “ANT+ Heart Rate Monitor”, “ANT+ Bike Cadence Sensor”, “ANT+ Bike Speed Sensor”, “Compass”, “Altitude” and “Screen”. Screen When you touch the screen, you can adjust the screen calibration if there is a difference on the response location. Step: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Screen”, a confirmation message will appear on the screen.
HOLUX FunTrek 132 Search heart rate monitor sensor, the steps are: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Heart Rate Monitor”, and press the “Search” button. After searching match heart rate monitor sensor, the device will display the list. Select the heart rate sensor that you need, and press the confirmation button to enable the function. The heart rate information will be displayed on the left-key info page.
HOLUX FunTrek 132 The details page displays the sensor’s information, such as Serial number; manufacture ID, model number, hardware version and software version. The model number of Cadence sensor is 20. ANT+ Bike Speed Sensors (optional) Step: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Speedometer”, and press “Search” button. After searching match speed sensor, the device will display the list.
HOLUX FunTrek 132 hardware version and software version. The model number of Speedometer sensor is 30. Compass To use the compass for the first time, the compass reading is not accurate; please calibrate the compass. Step: On the main menu page, click Settings. Select “Sensor” to enter the sensor settings menu. Select “Compass”. Press the button to calibrate the compass. Altimeter Users can use GPS to calibrate or manually calibrate the altimeter.
HOLUX FunTrek 132 System Left key- Info pages Use the “Left key- Info pages” to set the project displayed on Trip information and the auto-flip. Select pages You can select 1 ~5 information page to set the shortcuts for the “Left key- Info pages”. Step: On the main menu page, click Settings. Select “System”. Select” “Left key- Info pages”. Select” “Select pages”. You can select by checking items to be displayed for the Left Key operation.
HOLUX FunTrek 132 Time to flip Flip page time is the selected time interval to automatically switch among Info Page for the Left Key operation. Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select” “Left key- Info pages” to enter the left menu options. From the list, select” “Time to flip” to automatic exchange the information page at a preset time. When completed, it returns to main menu page.
HOLUX FunTrek 132 Screen Lock Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Screen lock” to enter the screen lock mode options. Select your option, and when completed, it returns to main menu page. Backlight Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Backlight” to enter the backlight mode options.
HOLUX FunTrek 132 Coordinates Setup Coordinates Format User can choose the appropriate format for their use. Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Set Coordinate” to view the coordinate lists. Select “Coordinate Format” to set the coordinate format. When completed, it returns to the previous screen. User Grid: Select User Grid in Coordinates Format List, and enter the parameter page.
HOLUX FunTrek 132 Coordinate Datum Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Set Coordinate” to view the coordinate lists. Select “Coordinate Datum” to set the coordinates. If you select “Beijing1954” or “Xian80” datum, you have to input the parameter. “a” and “1/f” cannot be edited. When completed, it returns to the previous screen. Customizing the Coordinate Datum: On the “Datum” page, select “User Datum”.
HOLUX FunTrek 132 Units Users can set the units of Speed/ Distance. Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Units” to enter the options list. Select “Metric” or “Imperial” units. When completed, it returns to the previous screen. Time Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Time”. Select “Time Format”.
HOLUX FunTrek 132 Select “Storage media”. Select “Holux Internal Memory” or “SD card”. When completed, a “Change will not take effect until the device restarts. Restart it right now?” message appears on the screen. User can restart the device to complete the setting. Language In the Language setup menu you can change the language interface. Available options are: Simplified Chinese, Traditional Chinese and English.
HOLUX FunTrek 132 MSAS/WAAS/EGNOS Enable the function to improve the GPS positioning accuracy. Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “MSAS/WAAS/EGNO”. Click “Open” to enable the MSAS/WAAS/EGNO function. Show tips at start Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Show tips at start”. Select “Open” to show tips when you restart the device.
HOLUX FunTrek 132 Alerts Step: On the main menu page, click “Settings” icon to enter the settings page. Select “System Settings”. Select “Alert” to enter the alert lists. Select “Distance”, “BAR Altitude”, “Speed” or “Time” button to set the alert. Select “On (Click to input)” to enter the Digital Keypad, and then enter the appropriate value. Note: Before use altimeter function, please read the section of Product Caution/ About the altimeter.
HOLUX FunTrek 132 Profiles Step: On the main menu page, click “Settings” icon to enter the settings page. Click “Profiles” icon to select “Current settings” or “Factory defaults”. Click “Factory defaults” to restore the factory default settings. Notes: the device can storage 10 settings. About You can get the software version information of the operation system (OS) and applications for this device.
HOLUX FunTrek 132 ezTour Plus Installation To download the recorded track log and view it on your computer, first, you will need to install the bundled ezTour Plus. Insert the bundled installation CD into the computer’s CD drive to install ezTour Plus. For details, please refer to the included ezTour Plus user manual.
HOLUX FunTrek 132 Website: www.holux.
