- HAI OmniPro II Owner's Manual
Table Of Contents
- INTRODUCTION
- OVERALL DESCRIPTION
- SECURITY SYSTEM OPERATION
- Disarming the Security System and Silencing Alarms
- Arming the Security System
- Using Shortcut Keys
- Quick Arm
- Bypassing Zones
- Restoring Zones
- What To Do When You Come Home
- What Happens When the Alarm is Activated
- Emergency Keys
- Duress Code Entered or Duress Alarm Activated
- Alarm Reset
- Alarm Cancel
- Trouble Indications
- Codes
- Duress Code
- Panic Switches
- Area Arming
- GOTO Area
- Testing Your System
- CONTROL
- Control Commands
- About UPB
- HAI Lighting Control (HLC) Format
- About CentraLite
- About Lutron RadioRA
- About ALC
- About X-10
- House Codes
- Unit Numbers
- Scrolling Through Names
- Controlling Units
- Timed Commands
- Status of a Unit
- Internal Flags
- Controlling Outputs
- All On / Off
- Leviton Scene Control
- Buttons
- Temperature Control
- HAI RC-Series Thermostats
- Programmable Energy Saver Modules (PESMs)
- Temperature Alarms
- Humidity
- Status
- Event Log
- Messages
- TELEPHONE CONTROL
- Telephone Interface
- In-House Phones
- Remote Phones
- Phone Access Denied - Remote Lockout
- Alternate Method
- Main Menu
- 1 - Control
- 2 - Security
- 3 - Button
- 4 - All
- 5 - Temperature
- 6 - Status
- 7 - Events
- 8 - Message
- 9 - Good-Bye
- Panic Button over the Phone (# # # # # #)
- Emergency Dial-Out
- Digital Dialer
- Voice Dialer
- PC Access
- Built-In Ethernet Port
- Controller IP Address, Port Number, and Encryption Key
- OmniPro II Ethernet Connections
- Connecting to Network via PC Access
- Dynamic DNS
- SETUP
- UNDERWRITER'S LABORATORIES REQUIREMENTS
- FEDERAL COMMUNICATION COMMISSION NOTICE:
- CANADIAN INDUSTRY CANADA NOTICE
- APPENDIX A - DIAL OUT PLANNER
- APPENDIX B - TEXT DESCRIPTION CHARACTER CODES
- APPENDIX C - VOICE DESCRIPTION CODES
Button and Event Programs
Selecting 2 (BUTTON), from the "Edit When" menu, sets up a program to be activated when a macro button is executed or an
event occurs. The user is prompted to specify the button/event that activates the program:
BUTTON:
ENTER BUTTON #=MENU
↓
A specific macro button may be activated by entering the button number followed by the ' # ' key, or by using the arrow keys to
scroll through a list of buttons.
To program specific event buttons (i.e. Front Door Opens, Security Armed Away, Porch Light Turns On, etc.), press the ' # ' key
to bring up a menu of event button types:
BUTTON TYPE
1=CTRL 2=SEC 3=ZONE
↓
4=ALL 5=ALARM 6=X-10
7=MISC 8=MSG 9=SWITCH ↑
After the event button is specified, the display returns to the Edit Program menu.
Control Unit / Switch Press Event Buttons
This Event Button is activated upon the following:
• When the specified Unit is turned on or off
• When the top-rocker or bottom-rocker is pressed on a UPB, RadioRA, or ALC switch
• When a button is pressed on a UPB 6-Button or 8-Button Keypad
• When a button is pressed on a RadioRA Master Control
• When a button is pressed on a ALC 4-Button Scene Switch Module
Press the 1 (CTRL) key to select the "When Command" for a control unit event.
UNIT:
ENTER UNIT
↓
The unit may be selected by entering the unit number followed by the ' # ' key or by using the arrow keys to scroll through a list of
unit names. Select the desired unit. Next, you are prompted to specify the event that activates the program:
WHEN Porch Light:
0=OFF 1=ON 2=SWITCH
Press the 0 (OFF) key to select when the unit turns off or press the 1 (ON) key to select when the unit turns on (this program is
executed whenever the unit is turned off or on).
Press the 2 (SWITCH) key to select only when the top-rocker or bottom-rocker is pressed at a UPB, RadioRA, or ALC Switch
(locally at the Switch) or when a button is pressed on a keypad.
SWITCH:
0=OFF 1=ON 2-11=SW1-SW10
Press "0" to select only when the bottom-rocker (off) is pressed on the Switch. Press "1" to select only when the top-rocker (on)
is pressed on the Switch. Press "2-9" (see the Corresponding Switch Table) to select when that button is pressed on a keypad.
Press the ' # ' key to enter your selection.
Page 61