Item #1005 711 209 Model #AM909-NI USE AND CARE GUIDE HERITAGE POINT LED 25 IN. CEILING FAN Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST Saturday 1-800-986-3460 HOMEDEPOT.COM/HOMEDECORATORS Visual instruction of how to install this fan: Visit www.homedepot.
Table of Contents Table of Contents .......................................................... 2 Safety Information ......................................................... 3 Operation ......................................................................17 Remote Control Operating Instructions ..................................17 Reverse Switch Operating Instructions ..................................18 Warranty .........................................................................
Safety Information 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less.
Warranty The manufacturer warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser. The manufacturer warrants the light kit (excluding any glass), to be free from defects in workmanship and material present at time of shipment from the factory for a period of five years after the date of purchase by the original purchaser.
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware not shown to actual size. AA BB CC DD Part Description Quantity AA Plastic wire nut 3 BB Blade attachment screw and fiber washer 10 CC 1.5V AAA battery 2 DD Extension cord 1 5 HOMEDEPOT.COM/HOMEDECORATORS Please contact 1-800-986-3460 for further assistance.
Pre-Installation (continued) PACKAGE CONTENTS A B C D E F H G I J K N L O M Part Description Quantity Part Description Quantity A Mounting bracket (preassembled) 1 I Blade arm 3 B Canopy ring (preassembled) 1 J Light kit mounting plate 1 C Canopy 1 K 18W LED Light kit 1 D Hanger ball / downrod assembly 1 L Glass shade 1 E Coupling cover 1 M Front guard 1 F Rear guard 1 N Receiver 1 G Fan motor assembly 1 O Remote control 1 H Blade 3 6
Installation MOUNTING OPTIONS NOTE: You may need a longer downrod to maintain proper blade clearance when installing on a steep, sloped ceiling. The maximum angle allowable is 18° away from horizontal. If the canopy (C) touches the hanger ball / downrod assembly (D), turn the canopy (C) 180° before attaching the canopy (C) to the mounting bracket (A).
Assembly Assembling the rear guard on the fan motor assembly 1 □ Remove three rear guard mounting screws (EE) from the rear guard (F) on the top of the fan motor assembly (G). □ Attach the rear guard (F) to the fan motor assembly (G) by tightening the rear guard mounting screws (EE) previously removed.
Assembly (continued) 2 3 Preparing the canopy Preparing the motor □ Remove the canopy ring (B) from the canopy (C). □ □ Remove the two non-slotted canopy mounting screws with lock washers (FF) from the canopy (C), and loosen the slotted canopy mounting screws with lock washers (FF) on the canopy (C). Remove the cotter pin (GG) and clevis pin (HH), and loosen the two collar setscrews (II) from the motor collar.
Assembly — Hanging the Fan 5 Hanging the fan to the mounting bracket 6 Installing the mounting bracket to the electrical box WARNING: To reduce the risk of fire, electric shock or other personal injury, mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box. □ Pass the 120-volt supply wires through the center hole in the mounting bracket (A).
Assembly — Hanging the Fan (continued) 2 3 4 ON DIP N 2 3 NOTE: The frequencies on your receiver and remote control have been preset at the factory. Before installing the receiver, make sure the dip switches on the receiver and remote control are set to the same frequency. The dip switches on the remote control are located inside the battery compartment.
Assembly — Hanging the Fan (continued) 8 Making the electrical connections Black White Ground conductor WARNING: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire. Outlet Box WARNING: To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch. Black NOTE: The fan must be installed at a maximum distance of 20 ft.
Assembly — Hanging the Fan (continued) 9 Installing the canopy Outlet box WARNING: Make sure the tab on the mounting bracket (A) properly sits in the groove in the hanger ball / downrod assembly (D) before attaching the canopy (C) to the mounting bracket (A) by turning the canopy (C) until it drops into place. FF Slide the canopy (C) up to the ceiling. Make sure you have placed the wires safely into the outlet box.
Assembly — Attaching the Fan Blades 10 Attaching the blades to the blade arms □ Attach the blades (H) to the blade arms (I) using the three blade attachment screws and fiber washers (BB). Start a screw with fiber washer (BB) into the blade arms (I), but do not tighten. □ Repeat for the two remaining blade attachment screws and fiber washers (BB). □ Fasten the blade assemblies to the fan motor assembly (G). □ Tighten each screw securely starting with the center screw.
Assembly — Installing the Light Kit 12 Attaching the light kit mounting plate to the mounting ring □ Remove one of the three light kit mounting plate screws (QQ) from the mounting ring (RR) and loosen the other two screws. (Do not remove.) □ Place the key holes in the light kit mounting plate (J) over the two screws (QQ) previously loosened from the mounting ring (RR). Turn the light kit mounting plate (J) until the light kit mounting plate (J) locks in place at the narrow section of the key holes.
Assembly — Installing the Front guard 14 Attaching the front guard to the fan motor assembly CAUTION: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box. Turning power off using the fan switch is not sufficient to prevent electric shock. □ Remove six front guard mounting screws (TT) from the rear guard (F).
Operation REMOTE CONTROL OPERATING INSTRUCTIONS - Press and release the button to turn the fan on or off. - Press and release 1 time - turns the fan on high speed. - Press and release 2 times - turns the fan on medium speed. - Press and release 3 times - turns the fan on low speed. - Press and release 4 times - turns the fan off. - Press and release the button to turn the light on or off. Press and hold the button to activate the dimmer function.
Operation (continued) REVERSE SWITCH OPERATING INSTRUCTIONS The reverse switch is located on the top of the motor housing. Slide the switch to the left for warm weather operation. Slide the switch to the right for cool weather operation. NOTE: Wait for the fan to stop before reversing the direction of the blade rotation. Reverse switch Cool weather - (Clockwise Direction) An upward air flow moves warm air off the ceiling.
Troubleshooting WARNING: Make sure the power is off at the electrical panel box before you attempt any repairs. Refer to step 8 “Making the electrical connections” on page 12. Problem The fan will not start. The fan sounds noisy. The remote control is not working. Solution □ Check the main and branch circuit fuses or breakers. □ Check the line wire connections to the fan and switch wire connections in the switch housing.
Service Parts A K AA L B C BB D M E CC F N DD H G O I J Part Description A Mounting bracket (preassembled) B Canopy ring (preassembled) C Canopy D Hanger ball / downrod assembly E Coupling cover F Rear guard G Fan motor assembly H Blade I Blade arm J Light kit mounting plate K 18W LED Light kit L Glass shade M Front guard N Receiver O Remote control Part AA BB CC DD 20 Description Plastic wire nut Blade attachment screws and fiber washers 1.
Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST Saturday 1-800-986-3460 HOMEDEPOT.COM/HOMEDECORATORS Retain this manual for future use.
