Installation Guide

ManualsBrandsHome Decorators Collection ManualsOtherSedgewood 36-1/2 in. W Bath Vanity in White with Solid Surface Technology Vanity Top in Arctic with White Sink

Item# 1003 619 898

Item# 1003 619 905

Item# 1003 619 907

Item# 1003 619 896

Item# 1003 619 906

Item# 1003 619 897

Item# 1003 619 902

Item# 1003 619 900

Item# 1003 619 901

Model# PPLNKDCG24D

Model# PPLNKDVR24D

Model# PPLNKWHT24D

Model# PPLNKDCG30D

Model# PPLNKDVR30D

Model# PPLNKWHT30D

Model# PPLNKDCG36D

Model# PPLNKDVR36D

Model# PPLNKWHT36D

TOOLS REQUIRED

Hammer Safety goggles Phillips screwdriver Power drill

Measuring tape Wall hardware Caulk/sealant Level

HARDWARE INCLUDED

AA - Knob x 3 BB - Screw x 3

Installation

1 PREPARING FOR INSTALLATION

NOTE: Before installation, make sure all parts are present. Compare parts with

the Hardware Included list. If any part is missing or damaged, do not attempt to

install the product.

□ Determine the desired mounting location, and mark the wall where the unit

will be installed.

NOTE: For secure installation, the unit must be mounted to at least one wall stud.

3 POSITIONING THE CABINET

□ Move the cabinet into place, and use wood

shims to level the cabinet against the wall.

Use and

Care Guide

Vanity Combo

2 CUTTING THE OPENING FOR PLUMBING FIXTURES

NOTE: This step applies to vanity cabinets with full back panels only.

□ Locate and mark plumbing on the back panel.

□ Drill a pilot hole through the back panel.

□ Use a keyhole saw to cut an opening for the plumbing fixtures.

4 BEFORE BEGINNING ASSEMBLY

□ Read directions thoroughly

□ Decide on right or left hand door conguration

□ Perform door / drawer swap prior to vanity installation.

HOMEDEPOT.COM

Please contact 1-888-774-8062 for further assistance.

Summary of content (4 pages)

PAGE 1
Use and Care Guide Model# PPLNKDCG24D Model# PPLNKDVR24D Model# PPLNKWHT24D Model# PPLNKDCG30D Model# PPLNKDVR30D Model# PPLNKWHT30D Model# PPLNKDCG36D Model# PPLNKDVR36D Model# PPLNKWHT36D Vanity Combo TOOLS REQUIRED Item# 1003 619 898 Item# 1003 619 905 Item# 1003 619 907 Item# 1003 619 896 Item# 1003 619 906 Item# 1003 619 897 Item# 1003 619 902 Item# 1003 619 900 Item# 1003 619 901 HARDWARE INCLUDED Hammer Safety goggles Phillips screwdriver Measuring tape Wall hardware Caulk/sealant Power d
PAGE 2
Door and Drawer Swap 5 DOOR SWAP INSTRUCTIONS □□ If swapping door and drawer locations, follow the instructions below. If using standard configuration, go to theInstallation Instructions on page 3. □□ Remove door from frame cabinet by using a #2 Phillips screwdriver to remove screws holding hinges in place. Save screws for reinstallation in a later step. 6 REMOVE DRAWERS □□ Remove both drawers by fully extending the drawer, then pushing the black plastic lever down on the right and up on the left side.
PAGE 3
Installation 11 INSTALLING THE CABINET □□ For wall stud installation, insert #12 x 3 in. screws with washers into the stud locations (not included). □□ For drywall installation, drill holes at the appropriate locations and insert toggle bolts with washers (not included). □□ For concrete wall installation, drill 1/4 in. holes at the appropriate locations and insert #12 wall anchors, followed by #12 x 3 in. screws (not included).
PAGE 4
Troubleshooting Problem Possible Cause Solution The doors do not align or the space is too big or too tight between the doors. The hinges are misaligned. Hold the door while loosening screws. Align the doors properly, and re-tighten the screws. Up — Down In — Out Left— Right Safety Information Please read and understand this entire manual before attempting to assemble, operate or install the product. Care and Cleaning □□ Use a water-dampened cloth to clean the cabinet. Avoid using abrasive cleaners.