Item #688-762 Model #YG493OD-ORB USE AND CARE GUIDE KENSGROVE (OUTDOOR) 72 IN. CEILING FAN Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST Saturday 1-800-986-3460 HOMEDEPOT.
Table of Contents Table of Contents .......................................................... 2 Operation ......................................................................17 Wall Switch Operating Instructions ........................................17 Reverse Switch Operating Instructions ..................................18 Safety Information ......................................................... 3 Warranty .........................................................................
Safety Information 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs.
Warranty We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser. We also warrant that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of two years after the date of purchase by the original purchaser.
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware shown to actual size unless noted otherwise in the table below.
Pre-Installation (continued) PACKAGE CONTENTS A B C D E F H G L J I M K Part Description Quantity Part Description Quantity A Mounting bracket (preassembled) 1 H Blade 8 B Canopy ring (preassembled) 1 I Blade arm 8 C Canopy 1 J 16 watt LED Light kit 1 D Canopy bottom cover (preassembled) 1 K Glass shade 1 E Hanger ball/downrod assembly 1 L Wall plate 1 F Coupling cover 1 M Wall control 1 G Fan motor assembly 1 6
Pre-Installation (continued) DUAL MOUNTING INSTRUCTIONS This ceiling fan is supplied with two types of hanging assemblies: the standard ceiling installation using the downrod with ball and socket mounting, and the "close-to-ceiling" mounting. The "close-to-ceiling" mounting is recommended in rooms with less than 8 ft. ceilings or in areas where additional space is desired from the floor to the fan blades.
Installation MOUNTING OPTIONS NOTE: You may need a longer downrod to maintain proper blade clearance when installing on a steep, sloped ceiling. The maximum angle allowable is 18° away from horizontal. If the canopy (C) touches the hanger ball/downrod assembly (E), then remove the decorative canopy bottom cover (D) and turn the canopy (C) 180° before attaching the canopy (C) to the mounting bracket (A).
Assembly — Standard Ceiling Mounting 1 2 Preparing the canopy Preparing the motor □ Remove the canopy ring (B) from the canopy (C). □ □ Remove the two non-slotted mounting bracket screws (BB) from the canopy (C), and loosen the slotted mounting bracket screws (BB) on the canopy (C). Remove the cotter pin (HH) and clevis pin (GG), and loosen the two collar setscrews (KK) from the motor collar.
Assembly — Close-to-Ceiling Mounting 1 2 Preparing the canopy □ Remove the canopy ring (B) from the canopy (C). □ Remove the mounting bracket (A) from the canopy (C) by loosening the four canopy mounting bracket screws (BB) on the top of the canopy (C). Remove the two non-slotted canopy mounting bracket screws (BB) and loosen the slotted canopy mounting bracket screws (BB).
Assembly — Hanging the Fan 4 Attaching the fan to the electrical box WARNING: To reduce the risk of fire, electric shock or other personal injury, mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box. □ Pass the 120-volt supply wires through the center hole in the mounting bracket (A).
Assembly — Hanging the Fan (continued) 6 Making the electrical connections WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. □ Disconnect the power and remove the existing wall plate and switch from the wall outlet box. □ Make wire connections as follows, using the wire nuts. a.
Assembly — Hanging the Fan (continued) 7 Installing the wall switch UU WARNING: Hook up in "series only". Do not connect the hot and neutral wires of the electric circuit to the wall switch - damage to the switch and possible fire could occur. M L WARNING: Remember to shut the power off at the circuit breaker or fuse box. □ Carefully tuck the wire connections inside the junction box (UU). Secure the wall switch (M) with the two wall switch screws (FF) provided.
Assembly — Hanging the Fan (continued) 8a 8b Standard ceiling mounting WARNING: Locking slots of the canopy (C) are provided only as an aid to mounting. Do not leave the fan assembly unattended until all four canopy screws (BB) are engaged and firmly tightened. WARNING: Make sure the tab on the mounting bracket (A) properly sits in the groove in the hanger ball (E) before attaching the canopy (C) to the mounting bracket (A) by turning the canopy (C) until it drops into place.
Assembly — Attaching the Fan Blades 9 Attaching the blades to the blade arms □ Attach the blades (H) to the blade arms (I) using the three blade attachment screws and fiber washers (CC). Start a screw with fiber washer (CC) into the blade arms (I), but do not tighten. □ Repeat for the two remaining blade attachment screws and fiber washers (CC). □ Tighten each screw securely starting with the center screw. Make sure the blade (H) is straight. □ Repeat these steps for the remaining blades (H).
Assembly — Installing the Light Kit 11 Attaching the LED light kit and glass shade CAUTION: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box. Turning power off using the fan switch is not sufficient to prevent electric shock. □ Remove one of the three light kit mounting screws (MM) from the mounting ring (VV) and loosen the other two screws. (Do not remove.
Operation WALL SWITCH OPERATING INSTRUCTIONS □ Your DC brushless motor is equipped with an automatically learned type wall control. Restore power to ceiling fan and test the wall control as below for proper operation. □ Install a 12V MN21/A23 battery (OO) (included) into the wall control (L). To prevent damage to the wall control (L), remove the battery if not used for long periods.
Operation (continued) REVERSE SWITCH OPERATING INSTRUCTIONS Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, and so on. NOTE: To operate the reverse function on this fan, press the for/rev button while the fan is running. Warm weather - (Counterclockwise Direction) A downward air flow creates a cooling effect. This allows you to set your air conditioner on a warmer setting without affecting your comfort.
Troubleshooting WARNING: Make sure the power is off at the electrical panel box before you attempt any repairs. Refer to the section “Making the Electrical Connections” on page 12. Problem The fan will not start. The fan sounds noisy. The remote control is not working. Solution □ Check the main and branch circuit fuses or breakers. □ Check the line wire connections to the fan and switch wire connections in the switch housing.
Service Parts A B C D I AA HH BB II CC JJ E KK DD F LL J EE MM G K FF NN L GG H M Part Description OO Part Description A Mounting bracket (preassembled) AA Plastic wire nut B Canopy ring (preassembled) BB Canopy mounting bracket screw with washer (preassembled) C Canopy CC Blade attachment screw and fiber washer D Canopy bottom cover DD Blade arm screw and lock washer (preassembled) E Hanger ball/downrod assembly EE Wall plate screw F Coupling cover FF Wall swit
Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST Saturday 1-800-986-3460 HOMEDEPOT.COM/HOMEDECORATORS Retain this manual for future use.