Installation Guide

Parts included :
1. Brackets (2X)
1-1.
Center bracket (1X for 39,46 sizes only)
2. Square End
3. Round End
4. Flat-Blade Key
5. Case Rail
6. Fabric Roll
7. Round Pin
8. PVC Spline
9. Square Pin
10. Temporary Pin - Dispose aer cung
11. Boom Axial Rod
12. Rubberized Rod Cover
13. Boom Rail
14. Tap-in Anchors (4X for 27,33 ; 6X for 39,46)
15. Screws (4X for 27,33 ; 6X for 39,46)
Tools needed (not included) :
1. Flathead Screwdriver
2. Philips-head Screwdriver
3. Measuring Tape
4. Pencil
5. Drill and Bits 1/4” and 1/8”
6. Level
STEP 2
Note Before Starng: This is a resizable product. Ask a store associate to trim your Cordless Zebra Shade if needed.
STEP 1
1A. Place Case Rail⑤ and Roller Fabric⑥ next to each other on a flat surface
making sure Square End② and Square Pin⑨, are aligned.
1B. Take Temporary Pin⑩ out from Fabric Roll⑥.
1C. Unfasten Case Rail⑤ with Flat-Blade Screw Key④.
1D. Adjust Case Rail⑤ to desired length.
1A
1B
1D
1C
This Cordless Zebra Shade is not washable. To remove dust, use a vacuum cleaner with a dust brush aachment end.
For cleaning any soiled areas, try gently rubbing the fabric using a water dampened cloth with a mild detergent only.
2A. Disassemble Boom Rail⑬ to reveal Rubberized Rod Cover⑫.
2B. loosen the Boom Rail⑬ with Flat-Blade Key④.
2C. Remove with scissors any excess of Rubberized Rod Cover⑫, so the Boom
Axial Rod⑪ spans desired length of Boom Rail⑬.
2D. Assemble Rubberized Rod Cover⑫ to Boom Rail⑬.
2E. Adjust both ends of the Boom Rail⑬ using Flat-Blade Key④.
2A
2B
2D
2C
2E
24
23
22
21
20
25
24
23
22
21
20
25
24
23
22
21
20
25
24
23
22
21
20
25
Inside Mount
Outside Mount
5B
5A
5C
1/4”
1/8”
Drywall
Wood or Studs
5D
20
21
22
23
24
25
26
27
28
29
30
31
20
21
22
23
24
25
26
27
28
29
26
27
28
29
30
31
23
24
25
26
27
28
29
5E
1-1
24
23
22
21
20
25
24
23
25
24
23
22
21
20
25
24
23
22
21
20
25
STEP 5
5A. Determine whether to measure for inside or outside mount.
5B. Place Brackets against wall at desired locaon, use tape measure and level to align, and mark screw holes.
5C-1. For mounng to drywall, ceiling or paneling, pre-drill pilot holes using 1/4" drill bit, insert Tap-In Anchors.
Install Brackets by fastening Screws into Tap-In Anchors.
5C-2. If mounng directly into wood or studs, pre-drill pilot holes with 1/8” drill bit.
Install Brackets with Screws provided.
5D. Slide the Case Rail into the Brackets at a slightly inclined angle while gently pushing it to contract the
springs of the Brackets. Keeping the springs of the Brackets contracted, finish the coupling moving the
Case Rail upwards. When doing so, you should hear a "click" sound.
5E. To operate properly, always pull from the center of the Boom Rail.
STEP 4
4A. Slide end of fabric through the middle of the fully assembled Boom Rail.
4B. Extend the fabric towards the Top Rail.
4C. Fold the fabric slowly twice, so that the end of the PVC Spline⑧ faces you.
4D. Insert the fabric into the back channel of the Case Rail using the PVC Spline.
Pull on fabric slightly to make sure it is secure. The product assembly is complete.
STEP 3
3A. Loosen Case Rail with Flat-Blade Key④.
3B. Extend Case Rail to desired length.
3C. Locate the Fabric Roll⑥ to be inserted into the Case Rail.
3D. Match the Case Rail and Fabric Roll so that the Square End of the case rail is inserted into the Square
Tip of the Roll⑨.
3E. Complete the inseron of the Fabric Roll into the Case Rail⑤ by matching Round End of Case Rail is
inserted into the Round Pin of the Fabric Roll.
3F. Adjust Case Rail with Flat-Blade Key④, leaving a small amount of space for part to operate
smoothly without jamming.
4A
4B
4C
4D
24
25
26
27
23
3C
3D
3F
3E
3A
3B
28
29
28
29
1-1